manualshive.com logo in svg

RuiDa KT332N, Руководство пользователя, Страница: 43 / 65

Поделиться
Скачать
RuiDa KT332N Скачать руководство пользователя страница 43

KT332N Cutting &engraving control system user manual V1.1

36

prompts "Resetting ...".
Press the [Esc] key to return to the previous menu.

8.6.11 Multiple origin points setting

In the menu, select the item “Origin point setting” and press the [OK] key to pop up the following
interface:

Figure 8.6.5-1

Move the red selection box to the "Multi-origin enable" item . Press [OK] to enable or disable the
multi-origin functions (the small square on the right side is displayed in red when it is enabled),
same as others setting. There is a [Setting] button for each item. Press the button and go to the
page shown as below. On this page the coordinates are displayed. And user can move the axes
manually to the origin position and press <Origin> to set each origin point.

Figure 8.6.5-2

Press the up, down, left and right keys to move the X or Y axis to the target position, press the
[Origin] key to set the origin point, and press Esc to cancel.

Содержание KT332N


































































Отзывы:

Нет отзывов