- 1 -
IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Important Safety Advice
When using electrical appliances, basic precautions
should always be followed to reduce the risk of fire,
electrical shock, and injury to persons, including the
following:
If the appliance is damaged, check with the supplier before
installation and operation.
Do not use this heater in the immediate surroundings of
a bath, shower or swimming pool.
Do not locate the heater immediately below a fixed socket
outlet or connection box.
Do not cover or obstruct in any way the heat outlet grille
located at the top of the heater or the heat outlet at the
base of the heater. Overheating will result if the heater is
accidentally covered.
This appliance is not intended for use by children or other
persons without assistance or supervision if their physical,
sensory or mental capabilities prevent them from using it
safely. Children should be supervised to ensure that they
do not play with the appliance.
In the event of a fault unplug the heater.
Unplug the heater when not required for long periods.
Ensure that furniture, curtains or other combustible
material are positioned no closer than 1 metre from the
heater.
Although this heater complies with safety standards, we
do not recommend its use on deep pile carpets or on long
hair type of rugs.
The appliance must be positioned so that the plug is
accessible.
Do not use this heater in series with a thermal control,
a program controller, a timer or any other device that
switches on the heat automatically, since a fire risk exists
when the heater is accidentally covered or displaced.
If the supply cord is damaged it must be replaced by the
manufacturer or service agent or a similarly qualified
person in order to avoid a hazard.
Caution: In order to avoid a hazard due to inadvertent
resetting of the thermal cut-out, this appliance must not
be supplied through an external switching device, such
as a timer, or connected to a circuit that is regularly
switched on and off by the utility.
The heater carries the Warning symbol indicating
that it must not be covered.
General
Unpack the heater carefully and retain the packaging for possible
future use, in the event of moving or returning the fire to your
supplier. Screws and rawl plugs, a remote control and batteries
are packed separately within the carton.
This fire incorporates a flame effect which can be used with or
without heating, so that comforting effect may be enjoyed at any
time of the year. The flame effect is provided by a low wattage
motor and three 60 watt lamps. Using the flame effect on its own,
therefore, requires little electricity.
The controls are located at the bottom right hand corner of the
appliance (see ‘z’ in
Fig. 1
). A choice of 750W or 1500W heat
output is provided by the fan heater, which is concealed at the top
of the heater (see ‘y’ in
Fig. 1
).
Please note: Used in an environment where background noise
is very low, it may be possible to hear a sound which is related to
the operation of the flame effect. This is normal and should not
be a cause for concern.
Electrical connection
WARNING – THIS APPLIANCE MUST BE EARTHED.
This heater must be used on an AC ~ supply only and the voltage
marked on the heater must correspond to the supply voltage.
Before switching on, please read the safety warnings and operating
instructions.
Installation
Do not connect appliance until properly fixed to the wall and the
instruction leaflet is read fully.
The minimum distances must be observed.
For installation of the appliance, care must be taken not to
damage concealed cables.
Please be careful while drilling holes.
This model is designed to be permanently fixed to a wall at a
minimum height of 300mm. The top wall bracket must be fitted
horizontally and the cable routed to the bottom of the heater.
A height of 550mm from the bottom of the heater to floor is
recommended for optimum viewing of the fuel bed (see
Fig. 1
for
recommended fixing dimensions).
For optimum viewing mark the top four screw fixing positions on
wall in accordance with the recommended fixing dimensions
(see
Fig. 2a
).
Drill holes with a 6mm drill bit.
Fix the bottom bracket to the appliance using the 2 black self
tapping screws provided (see
Fig. 2b
).
Fix the top wall bracket using the plugs and screws provided
(see
Fig. 2c
).
Carefully lift the heater up ensuring that the rear ledge of the heater
engages the top wall bracket and is sitting centrally positioned on
the bracket.
Mark the bottom bracket hole positions (see
Fig. 2d
) and remove
the heater.
Drill holes with a 6mm drill bit and insert plugs (see
Fig. 2e
).
Refit the heater to the wall fixing bracket and use the screws
provided to permanently fix the heater.
UK