RSF Woodburning Fireplaces OPEL+ KEYSTONE Скачать руководство пользователя страница 26

Страница: 26 / 36

OPEL PLUS KEYSTONE Owner's Manual

RSF Woodburning Fireplaces

FINISHING AROUND THE FIREPLACE

Finishing materials that cover the facing of the fireplace MUST BE NON-COMBUSTIBLE (e.g. brick, slate, ceramic

tile, etc.). Gypsum board is NOT an acceptable facing material. Gypsum boards cannot get closer to the fireplace

than the side standoffs and the top clearance specified in Table 1 (L) and shown in Figure 7 and Figure 8.

❖

WARNING: MAKE SURE TO RESPECT THE TOP CLEARANCE SPECIFIED IN TABLE 1 (L).

MANDATORY OPTIONS WITH TOP LOUVER BLOCKED

If you are planning to cover the top louver opening

with stone, you MUST install the Louver Blocking

Plate (provided) and TWO Gravity Vent Kits (sold

separately, see the "
Gravity vent Options" to select the kit of your

choice) to provide an evacuation path for the heat.

Neglecting to install both gravity vent kits will

result in overheating of the unit and may put your

safety at risk. Refer to each option's installation

instructions for details
Use only genuine RSF parts. The use of any

substitutes will decertify the system and may put

your safety at risk.

HEARTH EXTENSION

The area immediately in front of the fireplace must be protected by a non-combustible material such as brick, tile,

stone, or slate. Refer to Table 1 (G-H) for the depth and width that the hearth protection should extend beyond the

front and both sides of the door opening (see Figure 1). There is no minimum thickness required for the hearth

extension.

BENEATH HEARTH EXTENSION

If the OPEL+ KEYSTONE is installed on a non-combustible floor, the spark guard specified below is not required.
Install the spark guard provided (5" x 36" piece of sheet metal) halfway under the fireplace and halfway under the

hearth extension and centered on the door opening. The spark guard will extend 2½" beneath the fireplace. This

will make certain that sparks cannot lodge in this area and start a fire. If necessary, the provided spark guard can

be cut to the minimum width specified in Table 1 (I).
If you are preparing a raised installation, you will need

a custom-made spark guard, either a "Z" shaped

spark guard or a right-angle spark guard (see Figure

17). The Z-shaped spark guard must be used if the

height between the bottom of the fireplace and the

top of the non-combustible flooring of the hearth

extension is less than or equal to 2 ½". The height of

the Z-shaped spark guard must equal the distance

between the floor and the base of the unit and go

under the hearth extension and the fireplace by at

least 2½". If the unit is installed higher than 2 ½" from

the top of the flooring, a right-angle spark guard is

necessary. The sides of the right-angle spark guard

should be at least 2½" x 2½" and must be covered with non-combustible material. Any custom-made spark guard

must have the minimum width specified in Table 1 (I) and be installed centered on the door opening.



NOTE

: Custom-made spark guards are not supplied.

Figure 16 Louver Blocking Plate Installation

Figure 17 Special Custom-made Spark Guard

Non-

Combustible

Flooring

Right Angle

Spark Guard

(not provided)

More than 2 1/2"

Non-

Combustible

Flooring

Z-Shaped Spark

Guard (not

provided)

2 1/2" or less

RSF

Fireplace

Содержание OPEL+ KEYSTONE





































Результаты поиска

Содержание OPEL+ KEYSTONE

Отзывы:

Похожие инструкции для OPEL+ KEYSTONE

Бренды по названию

Популярные бренды

RSF Woodburning Fireplaces OPEL+ KEYSTONE, Руководство пользователя

Результаты поиска

Содержание OPEL+ KEYSTONE

Отзывы:

Похожие инструкции для OPEL+ KEYSTONE

Бренды по названию

Популярные бренды