RR Mechatronics RPI Скачать руководство пользователя страница 12

Страница: 12 / 98

Installation procedures and requirements

Users are not allowed to install and connect the instrument. The RPI must be unpacked, installed and

checked by a trained engineer prior to first operation.
Installation procedures and requirements are described in the Installation manual.

3.1 - Feed water requirements

The provided feed water quality will affect the performance of the RPI and is required to be within the

specifications mentioned below.
RR Mechatronics recommends that a Merck Millipore representative performs a water analysis prior to the

installation of the RPI to ensure your water supply meets the requirements.
This representative can also arrange for mitigations if laboratory water quality does not meet specifications.

Requirements:

Pressure:

1 – 6 bar

Flow rate:

> 5 L/min at 2 bar

Type:

Potable tap water

Temperature:

10 – 30 °C

Conductivity:

100 – 2000 μS/cm @ 25 °C

pH:

4- 10

Langelier Saturation Index (LSI):

< 0.3

Free total chlorine:

< 3 ppm

Installation procedures and requirements

MRN-184-EN Version 6 (05-01-2022)

Содержание RPI



































































































Результаты поиска

Содержание RPI

Отзывы:

Похожие инструкции для RPI

Бренды по названию

Популярные бренды

RR Mechatronics RPI, Инструкция по эксплуатации

Результаты поиска

Содержание RPI

Отзывы:

Похожие инструкции для RPI

Бренды по названию

Популярные бренды