27
RVV Gen II KO Service and Parts Manual
SECTION 3: Vender Programming
Pressing <enter> at the “Selection NN” prompt will allow
the assignment of cell(s) or the entire shelf to selection
NN. The display will show “Cell RC X” or “Entire Shelf
R X,” where R is the shelf number, C is the number of the
cell on shelf R, and X is the currently assigned state (1 =
assigned or 0 = unassigned). Using <up> or <down> will
allow you to cycle through the cells on shelf R. Pressing
<enter> at when “Cell RC X” or “Entire Shelf R X” is
displayed will cause X to flash. Press <up> or <down> to
toggle X between “0” and “1.” When the desired setting
is displayed, press <enter> to save the displayed status and
return to the “Cell RC X” or “Entire Shelf R X” prompt,
where X no longer flashes. If <exit> is pressed, the
display will return to the “Selection NN” prompt. In order
to save all settings, scroll to the “Save Settings” prompt
and press <enter>.
Notes: Selection pricing must be aligned with the space-
to-sales assignments.
It is not possible to create a Custom StS assignment with
products linked across shelves. If custom is entered after
setting the system to use Option 3, the system reverts to
Option 1 and starts the editing process.
Vend Evenly X
If <enter> is pressed at the “Vend Evenly X” prompt,
you will be able to toggle between “Vend Evenly 0”
(off) and “Vend Evenly 1” (on) by pressing <up> or
<down>. If “Vend Evenly X” is set to “0,” the controller
will vend in a FIFO (“first in, first out”) manner. FIFO
vending corresponds to vending from one cell until it is
completely sold out before vending from the next cell in
the space-to-sales. If “Vend Evenly X” is set to “1,” the
controller will vend evenly according to the space-to-sales
settings. Vending evenly means it will vend only once
from a cell before moving to the next cell in the space-to-
sales. Pressing <enter> at this point will save the current
setting. If <exit> is pressed during this editing process, the
controller will not save the setting and will take you back
to the “Vend Evenly X” prompt. Pressing <exit> at the
“Vend Evenly X” prompt will take you back to the “StS
Programming” prompt.
Conf
i
g Switches
If <enter> is pressed at the “Config Switches” prompt,
the controller will enter the machine configuration mode
by displaying “Cn –
Switch Description
X”, where the
“n” is the configuration switch number and “X” is the
current status (1 = enabled or 0 = disabled). Using <up>
or <down> will allow you to cycle through all available
configuration options. If <exit> is pressed anytime during
this operation the controller will return to the “Config
Switches” prompt. From the “Config Switches” prompt,
use <up> to proceed to the next prompt, “Correct Change.”
If <enter> is pressed the display will flash “X” (the current
status). Pressing <up> or <down> will cause the flashing
status to toggle between “0” (disabled) and “1” (enabled).
When the desired status is displayed, pressing <enter> will
save that status and return to the “Cn –
Switch Description
X” display.
The following information describes the various machine
configuration options.
•
C1 - Multi Price
This option is used to toggle between the single-price
and multi-price modes. In the single-price mode, the
price of selection 1 will be used for all selections. In
the multi-price mode, each selection can be set to a
different price.
If X = 0, single pricing is used.
If X = 1, multi-pricing is used.
•
C2 - Options Enable
This option is used to enable the Optional Features
Menu, which contains several more mode options
than available in the standard service menu (Correct
Change, Selection Blocking, Selection Discount,
Over-Ride Switches, etc.).
If X = 0, the Optional Features Menu will not appear.
If X = 1, the Optional Features Menu will appear.