manualshive.com logo in svg

Royal Enfield HIMALAYAN EURO IV 2017, Руководство по обслуживанию

Поделиться
Скачать
Royal Enfield HIMALAYAN EURO IV 2017 Скачать руководство пользователя страница 119

118

ROYAL ENFIELD    HIMALAYAN EURO IV VEHICLE SERVICE MANUAL

S.

No.

Fastener,  Size, Tool Usage, Precautions, Photos

Aggregate to Dismantle/

Instructions

12.6

D

Drag & Drop Links

Hold long hex bolt and
loosen nut, holding drop
links to drag link.

Remove long hex bolt.

Support swing arm and
remove inner race – drag
link back, to separate
drop links from drag link.

Remove the dust seals.

Hold hex bolt and
loosen nut holding drag
link to frame.

Support drag link and
remove hex bolt to
remove drag link from
frame along with dust
seals.

Hold hex bolts and
loosen hex U nuts
holding the 2 drop links
to swing arm bottom.

Remove the 2 hex bolts
one after the other to
release drop links along
with dust seals and inner
race from swing arm.

Hex nut: M10

Hex bolt M10

Double end spanner:17mm

Ring spanner: 14mm

NOTE:

It will be required to
dismantle centre stand
from frame for dismantling
drag link assembly.

NOTE:

The needle bearings
pressed into the drag and
drop links cannot be
replaced.

In case of bearing worn out
or damaged, the entire drop
links and/or drag link should
be replaced.

Содержание HIMALAYAN EURO IV 2017







































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды