Royal Enfield HIMALAYAN EURO IV 2017 Скачать руководство пользователя

Страница: 103 / 294

102

ROYAL ENFIELD HIMALAYAN EURO IV VEHICLE SERVICE MANUAL

Fastener, Size, Tool Usage, Precautions, Photos

Aggregate to Assemble/

Instructions

No.

Fork oil capacity:
455ml/leg

11.16

Front Fork Assy LH
& RH
Front Fork Internals

Assembly Outer tube
over inner tube assembly
bottom such that it is
seated fully against the
spindle taper.

Locate copper washer
on hex socket screw and
tighten outer tube to
piston – front fork.

Remove special tool

Gently tap plastic spacer
and oil seal, into fork end
till the oil seal is below
the lock ring groove in
the fork end

Assemble lock ring over
oil seal on the main tube

Press dust cap into fork
end till it is seated flush in
fork end.

Insert closed coil end of
the spring 1 (long) into
inner tube.

Fill 455ml of fork oil per leg

Locate thrust washer
and tube spacer inside
inner tube.

Assemble plain washer
over spacer and tighten
with the special hex cap nut.

Repeat process to
assemble other fork.

Содержание HIMALAYAN EURO IV 2017







































































































































































































































































































Результаты поиска

Содержание HIMALAYAN EURO IV 2017

Отзывы:

Похожие инструкции для HIMALAYAN EURO IV 2017

Бренды по названию

Популярные бренды

Royal Enfield HIMALAYAN EURO IV 2017, Руководство по обслуживанию

Результаты поиска

Содержание HIMALAYAN EURO IV 2017

Отзывы:

Похожие инструкции для HIMALAYAN EURO IV 2017

Бренды по названию

Популярные бренды