28
RSP-1576 Surround Sound Processor
Controls do not operate
•
Make sure that fresh batteries are installed in the remote.
•
Make sure that the IR sensor on the front panel is not blocked. Aim the
remote control at the sensor.
•
Make sure the sensor is not receiving strong IR light (sunlight, halogen
lighting, etc.).
•
Unplug the unit from the AC outlet, wait 30 seconds, and plug it
back to reset.
•
Confirm the IR Codeset set in the remote control and RSP-1576 are
matched to either Codeset 1 or Codeset 2.
Specifications
Audio
Total Harmonic Distortion
0.0006% (Analog Bypass)
0.003% (Digital Input)
Intermodulation Distortion
(60 Hz : 7 kHz, 4:1)
< 0.005%
Frequency Response
Phono Input
20 Hz - 20k Hz, ± 0.5 dB
Analog Bypass
10 Hz - 100k Hz, ± 1 dB
Digital Input
20 Hz - 20k Hz, ± 0.5 dB
Signal to Noise Ratio
(A-weighted)
Analog Bypass
112 dB
Digital Input
112 dB
Input Sensitivity/Impedance
Phono Level
3.5 mV / 47k ohms
Line Level
270 mV / 100k ohms
Balance Level
500 mV / 100k ohms
Preamp Output Level
Line Level
1.0 V
Channel Separation
(at 10k Hz
)
> 75 dB
Digital Audio
LPCM (up to 192kHz, 24-bit)
Dolby
®
Surround,
Dolby
®
TrueHD,
Dolby
®
ATMOS,
DTS-HD Master Audio,
DTS
X
Video
Input Resolutions
480i/576i, 480p/576p, 720p,
1080i, 1080p, 1080p 24Hz,
3D, 4K, UHD, 4K 60Hz, 4K HDR10
Output Resolution
480i/576i, 480p/576p, 720p
1080i, 1080p, 1080p 24Hz,
3D, 4K, UHD, 4K 60Hz, 4K HDR10
Color Space Support
sRGB, YCbCr 4:2:2, YCbCr 4:4:4
Deep Color Support
24-bit, 30-bit, 36-bit
HDMI Inputs/Outputs
7 inputs supporting HDCP 2.2, HDMI2.0a
2 outputs supporting HDCP 2.2, HDMI2.0a
Audio Return Channel
General
Power Consumption
60 watts
< 0.5 watt (standby)
Power Requirements
(AC
)
120 volts, 60Hz
230 volts, 50Hz
BTU
114 BTU/h
Dimension
(W x H x D)
431 x 144 x 348 mm
17 x 5
2
/
3
x 13
5
/
7
in
Front Panel Height
3U / 132.6 mm / 5
1
/
4
in
Weight
8.8 kg / 19.4 lbs
All specifications are accurate at the time of printing.
Rotel reserves the right to make improvements without notice.
Rotel and the Rotel Hifi logo are registered trademarks of The Rotel Co., Ltd. Tokyo, Japan.
“
Made for iPod,” and “Made for iPhone,” means that an electronic accessory
has been designed to connect specifically to iPod or iPhone, respectively, and
has been certified by the developer to meet Apple performance standards. Apple
is not responsible for the operation of this device or its compliance with safety
and regulatory standards. Please note that the use of this accessory with iPod,
or iPhone may affect wireless performance.
iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple
Inc., registered in the U.S. and other countries.
