34
RSP-1098
Surround Sound Processor
To change a setting on the SPEAKER SETUP
menu, place the highlight on the desired line
using the UP/DOWN buttons and use the +/
– buttons to toggle through the available set-
tings. To return to the MAIN menu, press the
ENTER button. Press the MENU/OSD button
on the remote to cancel the display and re-
turn to normal operation.
Advance Speaker Setup
ADV SPEAKER SETUP
SPEAKER:Front
CROSSOVER:100Hz
DOLBY:Small
DTS:Small
STEREO/MPEG:Large
MUSIC:Small
SPEAKER SETUP MENU
In most cases, the standard speaker configu-
ration described above is a global setting and
can be used for all surround modes. However,
the RSP-1098 provides the capability to cus-
tomize these settings for four different surround
modes: Dolby, DTS, Stereo, and Music. For
example, you could set up the Dolby and DTS
modes for 5.1 channel sound, while the Ste-
reo mode changes to a 2-speaker setup with
or without a subwoofer. In addition, the AD-
VANCED SPEAKER SETUP allows you to se-
lect a customized high-pass crossover frequency
for the front, center, surround, and surround
back speakers.
NOTE
:
In most systems, the default settings on
this menu will provide the most predictable
results and most users will not need to change
any settings. You should fully understand bass
management and have a specific reason for
needing a custom configuration before chang-
ing these settings. Otherwise, skip to the fol-
lowing topic, SUBWOOFER SETUP.
The available settings on the ADVANCED
SPEAKER SETUP menu are as follows:
SPEAKER (front/center/surround/cen-
ter back/subwoofer):
Select the set of
speakers to be configured with custom settings.
CROSSOVER (40Hz/60Hz/80Hz/
100Hz/120Hz/150Hz/200Hz):
Typi-
cally, the RSP-1098 uses a single master set-
ting for the high-pass and low-pass crossover
point between all SMALL speakers and the
subwoofer. This master crossover point is set
on the SUBWOOFER SETUP menu described
in the following section. When you first ac-
cess the ADVANCED SPEAKER SETUP menu,
the current master crossover point will be shown
on this line. Change the value of this line only
if you want the current speaker to have a dif-
ferent crossover point. For example, if your
master crossover is set to 80Hz, but you want
your front speakers to crossover to the sub-
woofer at 60 Hz, you would select 60Hz for
the front speakers on this line. This setting ONLY
affects redirected bass and does not affect the
LFE channel in any way. The OFF setting (avail-
able only for the subwoofer) sends a full-range
signal to your subwoofer so that you can use
its built-in low-pass filter.
NOTE
:
When a speaker is set to LARGE on
the SPEAKER SETUP menu or on this MENU,
the crossover setting is not available since,
by definition, a LARGE speaker plays full-
range with no bass redirection to the sub-
woofer and no crossover. Likewise, the OFF
setting for the subwoofer crossover is not avail-
able for SMALL speakers, since SMALL means
that the speaker will redirect its bass below a
given crossover point to the subwoofer. In
addition, the CROSSOVER setting is not avail-
able for the MULTI INPUT.
DOLBY (large/small/none):
Sets the
current speaker (shown in the first line) to
LARGE, SMALL, or NONE, overriding the
master setting from the SPEAKER SETUP menu.
This setting will ONLY take effect with Dolby
Digital or Dolby Pro Logic II decoding.
DTS (large/small/none):
The same op-
tions described for Dolby above, except these
settings ONLY take effect with DTS and DTS
Neo:6 decoding.
STEREO/MPEG (large/small/none):
The
same options described for Dolby above,
except these settings ONLY take effect in STE-
REO surround mode.
MUSIC (large/small/none):
The same op-
tions described for Dolby above, except these
settings ONLY take effect with any of the DSP
MUSIC surround modes.
NOTE
:
When the front speakers are set to use
the master crossover frequency on the AD-
VANCED SPEAKER SETUP menu, the surround
mode specific “large/small/none” settings
are not available for the other speakers. These
speakers will use the setting determined in
the basic SPEAKER SETUP menu.
Subwoofer Setup
SUBWOOFER SETUP
CROSSOVER:100hZ
DOLBY DIGITAL: 0dB
DOLBY PL II: 0dB
DTS: 0dB
STEREO/MPEG:+ 2dB
MUSIC: Off
MULTI INPUT:- 2dB
MAIN MENU
The SUBWOOFER SETUP menu allows selec-
tion of the master subwoofer crossover fre-
quency and independent adjustment of sub-
woofer level for each surround mode.
CROSSOVER (40Hz/60Hz/80Hz/
100Hz/120Hz/150Hz/200Hz/OFF):
This setting specifies a master low-pass filter
for the subwoofer and a corresponding high-
pass filter for all SMALL speakers in the sys-
tem at the selected frequency. To adjust the
crossover frequency, highlight the CROSSOVER
line using the UP/DOWN buttons. Then, use
the +/– buttons to chose the master crossover
point. The 80Hz or 100Hz crossover points
are the most common in home theater systems
and should be used unless you have a spe-
cific reason to choose a different crossover
point based on your specific speakers.
The OFF setting sends a full-range signal to
your subwoofer so that you can use its built-
in low-pass filter. With the OFF setting, a 100
Hz high-pass filter is activated for all SMALL
speakers in the system.
NOTE
:
The master crossover point can be over-
ridden with a custom crossover frequency for
the front, center, surround, or surround back
speakers in the ADVANCED SPEAKER SETUP
menu; however, in most systems the single
master crossover point should work well
DOLBY DIGITAL:
DOLBY PLII:
DTS:
STEREO/MPEG:
MUSIC:
MULTI INPUT:
These six lines allow you override the master
subwoofer level setting as determined on the
TEST TONE menu (see below) for each spe-
cific surround mode. When going to the SUB-
WOOFER SETUP menu from the MAIN menu,
the current surround mode is automatically
highlighted. Use the +/– buttons to adjust the
subwoofer level for the current surround mode.
The options are OFF (which turns off the sub-
Содержание RSP-1098
Страница 2: ......
