background image

5

Lights on/off 

(Optional Accessory) 

Activate Column Buttons 

(8 Total) 

Lower To Locks 

Height Limit Setting 

Battery Charge Indicator 

System Configuration 

Lock/Unlock 

Single/Pair/All Mode 

E-Stop 

Raise 

Lower 

Slow Lower 

Yellow, Green, Red

Activation LED’s

(8 Total)

Data Information 

Display and Buttons 

Quick Start Operating Instructions

Control Panel Diagram 

1.  The service area must be clear of all personnel before 

the vehicle is positioned.

WARNING  

Locate lift on level concrete surface with a 

minimum strength of 3000 psi.

2.  Spotting: Position the vehicle in the location where it is 

to be lifted.

Note: See Fig. 2 for the general arrangement of each lift 

column.

3. Loading:

Position one column at a lifting wheel location.  Position 

so that the forks are under the tire and the unit is pushed 

in as far as possible, Fig. 3.  Ensure fork width is adjusted 

to properly accommodate the tire/wheel size.  Turn on the 

Power Up Switch, Fig. 4.

4.  Using the Control Panel and the bus diagram as a 

reference (see graphic above), press the Activate Column 

Button relative to the location where the column was just 

placed.  The column will show Green when activated.

5.  Plug the fixed length communication cable from the cord 

reel into the bottom of the control panel.

6.  Position next column at second wheel using loading 

instructions from step 3.

7.  Run the reel-end of the communication cable from the 

first column and plug into the side of the control panel on 

the second column.   Turn on second column.  Again, using 

the Control Panel and the bus diagram as a reference, press 

the Activate Lift Button relative to the location of the second 

column.  The lift will show Green when activated.  The first 

lift you activated should now be flashing yellow on your 

control panel.

8.  Repeat step 5 thru 7 for remaining columns.  When 

the entire system of columns is complete, press the 

System Configuration Lock/Unlock button to lock the lift 

configuration for operation.

NOTE:  The electrical communication cables do not 

have to make a complete loop.  You do not have to plug 

the last lift back into the first lift. 

Содержание MCH418

















Отзывы: