background image

2

Index

Set-Up Instructions  .................................................. 2

Safety Instructions  ................................................... 4

Owner/Employer Responsibilities  .......................... 4

Quick Start Operating Instructions  ........................ 5

Emergency Lowering ................................................ 7

Detailed Operating Instructions .............................. 8

Battery Charging ........................................................ 9

Maintenance Instructions  ..................................... 10

Trouble Shooting ...................................................... 11

Lift Lockout/Tagout Procedure .............................. 12

Wiring Diagram ........................................................ 13

Set-Up Instructions

Follow these instructions to ensure a satisfactory set-up 

and operation of the lift.

•  After set-up and inspection of the lift, please return this 

booklet  to the literature package and give to lift owner/

operator.  Literature package should be kept attached to 

controls for easy access.

1.  Unloading:  Rotary’s Mobile Lift System units are shipped 

in the vertical position.

2.  After unloading, remove and discard protective 

wrapping. 

NOTE:  Unit is shipped without batteries and 
without power unit fluid.  Installation of both 
batteries and fluid MUST be completed prior 
to lift operation.

  Failure to do so will result in air 

entering the system.  The unit will then have to be 

bled.

3.  To move the column, remove protective banding and 

wheel clamps from wheel jack.  The forklift brackets can be 

removed from the side of the column if desired.

4.  Open power unit cover by removing the 3 M8 BHCS 

(Button Head Cap Screw).  Fill power unit tank with 

ISOVG32 hydraulic oil.  Tank capacity is approximately 11-

1/2 quarts (11 liters).  Fill until fluid is just barely visible on 

dipstick.

5.  Install two batteries in location shown, Fig. 1.  Through 

our research Rotary recommends Exide

®

 brand battery 

part number NG-27 or DEKA

®

 brand battery part 

number DC31DT.  Different batteries meeting the below 

specifications may be used but performance can vary.  

Recommended Battery Specifications:

12V DC Sealed Deep Cycle Battery

Size 31 Frame Group

105 AH Capacity (At 20 AH Rate)

Stud Terminals with Stainless Steel Wing nuts

Battery wires are clearly marked/labeled inside the unit 

itself.

Install tie-down straps on batteries as shown.  

Close lift and re-install M8 BHCS removed earlier.

After the batteries and fluid have been added, screw M20 

bolt and M10 socket head bolts clockwise on wheel jack 

and front of superstructure to adjust unloaded column 

ground clearance, Fig. 1.  Ground clearance is determined 

by how far the bolts are turned.  When the column is 

loaded, it will automatically lower to the floor.

WARNING  

 Permit only trained personnel to 

operate lift.  After reviewing these instructions, 

become familiar with the lift controls by running the lift 

through a few cycles before loading a vehicle on lift. 

Observe and heed SAFETY and WARNING labels on 

the lift.

                                                                           

WARNING  

 This motor has internal arcing or 

sparking parts.  To minimize the Risk of Explosion, DO 

NOT expose to flammable vapors.  

OPERATING CONDITIONS:  Lift is not intended for 

outdoor use or storage and has an operating ambient 

temperature range of 41º-104ºF (5º-40ºC).

DO NOT use lift in a manner other than intended.  

Included (but not limited to) examples of unapproved 

uses of the lift are: lifting vehicle by only one side, 

lifting different axles with a column pair (lifting on the 

diagonal), and lifting non-approved items. 

6.  Bleed mobile columns:

a.)  Raise forks 150-200mm do not lift forks high enough to 

engage locks.

b.)  Loosen bleed screw to release air from system.

c.)  Close screw and repeat steps a and b until there is no 
air in the system and fluid runs clear. 

Содержание MCH418

















Отзывы: