background image

Rosen Entertainment Systems 

 

Copyright 2007 all rights reserved 

HE0780D Installation Guide 

 

AP1024  Rev A 

 

 

Page 9 

Selecting FMM pre-sets 

For best operation, the FMM Pre-set selection should be on a station which is not in use or has weak 
broadcast in your area. 

Solution: 

You can also check www.RosenDealerCentral.com. This site provides you with the best 

stations in your local area. Select a corresponding FMM Station when available. 

 

Reducing audio or video noise 

Audio or video noise may be induced into the system from sources ranging from harness location, power 
point to poor grounding. 

Solution: 

Re-route the wire harnesses to avoid passing over other harnesses or near electrical 

motors. 

Solution: 

Try relocating the ground point to factory ground point or factory ground wire. 

Solution: 

In some cases, inline audio filters may be required. Contact Rosen for support on 

selection of a filter. 

 

Missing Channel B Audio  

System includes a monitor A and monitor B.  Monitor A is channel “A” on headphones and monitor B is 
channel “B” on headphones.  If audio is not present, check the following. 
             

Solution: 

Check A/B switch on headphones. 

 

Solution: 

Reset the system 

             

Solution: 

Check all cable connections 

             

Solution: 

Please refer to “Install Set-up Menu”. 

Solution: 

Force channel B via Installer Setup menu 

 
 

Service and optional parts list 

 

Part Number

 

 

Description

 

 

            

Part Number

                

Description

                   

 
AP1006  

             IR Remote Control                     AC3323  

           External Wireless FMT 

AP1007  

 

IR Game Controller                    AP1003  

           Interface Module 

AC3640 

 

2 Channel IR Headphones         AP1041  

           Monitor Black Harness 

AP1008  

 

Power Harness                           AP1042  

           Monitor Gray Harness 

AP1010  

 

Interface Extension Harness      AP1011  

           Monitor Aux Harness 

AP1012  

             Remote IR Harness                    AP1019  

           Hardware Pack 

AC3196 

 

External Wired FMM                   AP1026  

           Quick Reference Card 

AP1021  

 

Owners Manual 

Содержание HE0780D











Отзывы: