manualshive.com logo in svg

Rosemount P300, Инструкция по установке и эксплуатации

Поделиться
Скачать
Rosemount P300 Скачать руководство пользователя страница 31

Section

5-1

5

Specifications and Reference 
Data

INSTRUMENT 
SPECIFICATION

TABLE 5-1.  Pressure Specification and 
Ranges.

Pressure Accuracy

Combined nonlinearity, hysteresis, and repeatability

All pressure range versions ±0.075% Full Scale.

Pressure Temperature Effects 

All versions 32 to 104 °F (0 to 40 °C) ±0.5%. 

Pressure Output

Type: Handpump and Volume Adjuster.
Pump Range: –12.75 to 300 psi gage. (–0.88 to 20.7 bar).
Pressure/Vacuum Changeover: Manual Switch (Pressure/Vacuum
only).

Maximum Working Pressure

The pressure can be exceeded by up to two times its range, causing 
negligible validation change. 

Burst Pressure

Option Code 4 (150 inH

2

O): 184 psi (12.7 bar).

Option Code 5 (750 inH

2

O): 350 psi (24 bar).

Option Code 6 (100 psi): 375 psi (25.9 bar).
Option Code 7 (300 psi): 375 psi (25.9 bar).

ELECTRICAL 
SPECIFICATIONS

Electrical Safety

Meets EN61010-1 as applicable.

Power Supplies

External dc supply: 3.5 to 12V (Max) dc.
Internal batteries: Four D cell or NiCad rechargeables.

Battery life 

Standard D cell: 40 hours.
Alkaline D cell: 70 hours.
NiCad (4 Ah): 18 hours.
Battery charge current (NiCad only): 400 mA.

Voltage Measurement Range

No.

Range

4

150  in

5

750  in

6

100 psi

7

300 psi

Содержание P300

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды