manualshive.com logo in svg

Rosemount 702, Справочное руководство

Поделиться
Скачать
Rosemount 702 Скачать руководство пользователя страница 50

Reference Manual

00809-0200-4702, Rev BA

June 2010

Rosemount 702

5-16

POWER MODULE 
REPLACEMENT

Expected power module life is ten years at reference conditions.

(1)

When the power module needs to be replaced, remove the power module 
cover and the power module (Part Number 00753-9220-0001) then replace 
the cover. Tighten to specification and verify operation.

Handling Considerations

The power module with the wireless unit contains two “C” size primary 
lithium/thionyl chloride batteries. Each battery contains approximately 2.5 
grams of lithium, for a total of 5 grams in each pack. Under normal conditions, 
the battery materials are self-contained and are not reactive as long as the 
batteries and the battery pack integrity are maintained. Care should be taken 
to prevent thermal, electrical or mechanical damage. Contacts should be 
protected to prevent premature discharge.

Use caution when handling the power module, it may be damaged if dropped 
from heights in excess of 20 feet.

Battery hazards remain when cells are discharged.

Environmental Considerations

As with any battery, local environmental rules and regulations should be 
consulted for proper management of spent batteries. If no specific 
requirements exist, recycling through a qualified recycler is encouraged. 
Consult the materials safety data sheet for battery specific information.

Shipping Considerations

The unit was shipped to you without the power module installed. Please 
remove the power module prior to shipping.

Each power module contains two “C” size primary lithium batteries. Primary 
lithium batteries are regulated in transportation by the U.S. Department of 
Transportation, and are also covered by International Air Transport 
Association (IATA), International Civil Aviation Organization (ICAO), and 
European Ground Transportation of Dangerous Goods (ARD). It is the 
responsibility of the shipper to ensure compliance with these or any other 
local requirements. Please consult current regulations and requirements 
before shipping.

(1)

Reference conditions are 70° F (21° C), transmit rate of once per minute, and routing data 
for three additional network devices.

Содержание 702





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды