background image

KSC-54/56

 

STAND ASSEMBLY

 

Before you begin assembling the stand, check that all the parts
were supplied. You will also need to have a Phillips screwdriver.

fig.parts.eps

 

Items required for assembly

 

* Finger-tighten the screws to assemble the stand provisionally, and then use a screwdriver to tighten the screws firmly. Perform the assembly on a stable and 

flat location.

* Do not allow the pedal cord or power cord to get twisted or pinched while assembling the stand.
* Do not set up the instrument on long-piled carpeting. This can cause instability in the stand and unsteadiness in the pedals, possibly resulting in damage to 

the unit.

* The piano unit and the surface of the stand are very delicate; handle with care to avoid scratching them.
* Do not place the piano unit directly on the floor. Doing so will damage the bottom panel case and the connectors and holders on the bottom of the piano.

 

1.

 

As shown in the illustration, place the left and right side boards on the 
pedal board so that the metal brackets are on the inside, and fasten 
them provisionally using screws “a” (M5 x 40 mm).

 

2.

 

After you have provisionally tightened screws “a” (four locations), use a 
screwdriver to tighten them firmly.

 

When attaching the pedalboard, do not allow any gap to remain 
between the side board and pedalboard when the pieces are 
assembled.

fig.1-1-1.eps

 

3.

 

With the help of another person, raise the left and right side boards to an 
upright position.

 

* Take care that the pedal boards are not twisted.

fig.1-1-2.eps

 

4.

 

Loosen the screws attached to the left and right side boards 
approximately three turns, so that they protrude about 3 mm, as shown 
in the illustration.

fig.1-2.eps

 

5.

 

Hook the metal brackets of the rear board over the screws you loosened, 
as shown in the illustration.

 

6.

 

Use four screws “b” (M5 x 20 mm) to provisionally fasten the pedal 
board.

 

7.

 

Securely tighten the two side board screws and four pedal board screws.

 

* When attaching the rear board, before tightening the screws, adjust 

things as necessary at all the points where there are screws so as to 
assure that the rear board is aligned in parallel with the pedal 
board.

 

fig.1-3.eps

 

Prepare an area in which you can perform the assembly safely.

Make sure that another person is on hand to help with the assembly and setup.

Be very careful, when you assemble and move the piano, to make sure that you do not drop it on your hands or feet.

To move the piano, lift it carefully—all the while keeping it level.

Do not use a power tool (e.g., an electric screwdriver) to assemble the stand. You risk damaging or stripping the screws.

This product is quite heavy; when moving it, please obtain the help of a sufficient number of other people so that it can be 
moved without danger or strain.

To prevent accidental ingestion or choking, any screws you remove and cords you disconnect must be placed in a safe 
location, out of the reach of children. 

 

Parts Check

b

a

A

B

C

D

KSC-54

A

 

A: Side Board (left)

B: Side Board (right)

C: Pedal Board

D: Rear Board

a: Screw “a” (M5 x 40 mm) x 4

b: Screw “b” (M5 x 20 mm) x 6

Phillips screwdriver

 

Assembly Procedure

 

1

Assembly procedure

At first, assemble the entire stand in a temporary fashion, without really tightening the screws. Then, after checking the overall alignment of the 
boards (and gently shifting certain parts where necessary), go around and tightly fasten each of the screws.

If necessary, spread out a blanket or similar material to prevent the stand or floor from being scratched during assembly.

Be careful not to pinch the pedal cord during assembly.

Screw “a”

(2 screws)

Screw “a”

(2 screws)

Leave the pedal 

cord extended

Improper

Space

Side 

board

Side 

board

Correct

Pedal

board

Pedal

board

 

Space

3 mm

Screw “b” (4 pieces)

Screws you loosened

in step 4 (2 screws)

Rear view

 

1.

 

Align the screws on the bottom of the piano (one each at left and right) 
with the metal brackets on the side boards, and while keeping the front 
of the piano slightly raised, pull it toward yourself to engage the screws 
in the metal brackets.

 

* When handling the piano, firmly grasp it. Be careful, so you do not 

get your fingers pinched.

 

2.

 

Fasten the piano to the stand with the screw “b” (M5 x 20

 

 

 

mm).

fig.2-1.eps

 

1.

 

Connect the pedal cord to the Pedal connector.

 

ˆ

 

* Plug the pedal cord all the way into the Pedal connector.

 

Models with a power cord

 

1.

 

Connect the included power cord to the AC In jack located on the piano’s 
bottom panel.

 

2.

 

Plug the power cord into an AC outlet.

 

Models with an AC adaptor

 

1.

 

Connect the supplied AC adaptor and AC cord.

 

2.

 

Connect the AC adaptor to the DC In jack on the rear panel.

 

3.

 

Plug the power cord into an AC outlet.

 

As needed, use the plastic-coated clips on the bottom of the piano to 
secure the power cord and pedal cord.

Turn the adjuster to lower it until the adjuster is in firm contact with the 
floor. In particular, when you’ve placed the piano on carpet, you must 
turn the adjuster until it is pressing firmly against the floor.
* The pedal may be damaged if there is a gap between the adjuster 

and the floor.

fig.5-1.eps

 

1.

 

Close the keyboard lid.

 

2.

 

Disconnect the power cord or AC adaptor.

 

3.

 

Raise the stand’s adjuster.

 

4.

 

Keep the piano level when you lift it, and take care not to pinch your 
hands or drop the piano on your feet.

 

5.

 

After placing the piano in its new location, perform steps 

 of 

the “Assembly Procedure.”

 

Copyright© 2009 ROLAND CORPORATION

 

All rights reserved. No part of this publication may be reproduced in 
any form without the written permission of ROLAND CORPORATION.

 

2

Install the piano onto the stand

3

Connecting the pedal cord

4

Connecting the power cord

Screw “b”

Please don’t get your
fingers pinched.

Pull the piano toward yourself while 
keeping the front slightly raised.

Power cord

 

5

Fastening the cords

6

Adjusting the adjuster

Rear view

AC adaptor cord

Coated clip

 

Adjuster

 

When Moving the Piano

4

6

Be sure to keep this leaflet together with the owner’s manual.

 

KSC-54/56

 

1

KSC-54_56_l_assemble_e.fm 1 ページ 2009年10月14日 水曜日 午前10時37分

Содержание KSC-54/56









Отзывы: