KSC-54/56
STAND ASSEMBLY
Before you begin assembling the stand, check that all the parts
were supplied. You will also need to have a Phillips screwdriver.
fig.parts.eps
Items required for assembly
* Finger-tighten the screws to assemble the stand provisionally, and then use a screwdriver to tighten the screws firmly. Perform the assembly on a stable and
flat location.
* Do not allow the pedal cord or power cord to get twisted or pinched while assembling the stand.
* Do not set up the instrument on long-piled carpeting. This can cause instability in the stand and unsteadiness in the pedals, possibly resulting in damage to
the unit.
* The piano unit and the surface of the stand are very delicate; handle with care to avoid scratching them.
* Do not place the piano unit directly on the floor. Doing so will damage the bottom panel case and the connectors and holders on the bottom of the piano.
1.
As shown in the illustration, place the left and right side boards on the
pedal board so that the metal brackets are on the inside, and fasten
them provisionally using screws “a” (M5 x 40 mm).
2.
After you have provisionally tightened screws “a” (four locations), use a
screwdriver to tighten them firmly.
When attaching the pedalboard, do not allow any gap to remain
between the side board and pedalboard when the pieces are
assembled.
fig.1-1-1.eps
3.
With the help of another person, raise the left and right side boards to an
upright position.
* Take care that the pedal boards are not twisted.
fig.1-1-2.eps
4.
Loosen the screws attached to the left and right side boards
approximately three turns, so that they protrude about 3 mm, as shown
in the illustration.
fig.1-2.eps
5.
Hook the metal brackets of the rear board over the screws you loosened,
as shown in the illustration.
6.
Use four screws “b” (M5 x 20 mm) to provisionally fasten the pedal
board.
7.
Securely tighten the two side board screws and four pedal board screws.
* When attaching the rear board, before tightening the screws, adjust
things as necessary at all the points where there are screws so as to
assure that the rear board is aligned in parallel with the pedal
board.
fig.1-3.eps
•
Prepare an area in which you can perform the assembly safely.
•
Make sure that another person is on hand to help with the assembly and setup.
•
Be very careful, when you assemble and move the piano, to make sure that you do not drop it on your hands or feet.
•
To move the piano, lift it carefully—all the while keeping it level.
•
Do not use a power tool (e.g., an electric screwdriver) to assemble the stand. You risk damaging or stripping the screws.
•
This product is quite heavy; when moving it, please obtain the help of a sufficient number of other people so that it can be
moved without danger or strain.
•
To prevent accidental ingestion or choking, any screws you remove and cords you disconnect must be placed in a safe
location, out of the reach of children.
Parts Check
b
a
A
B
C
D
KSC-54
A
A: Side Board (left)
B: Side Board (right)
C: Pedal Board
D: Rear Board
a: Screw “a” (M5 x 40 mm) x 4
b: Screw “b” (M5 x 20 mm) x 6
Phillips screwdriver
Assembly Procedure
1
Assembly procedure
•
At first, assemble the entire stand in a temporary fashion, without really tightening the screws. Then, after checking the overall alignment of the
boards (and gently shifting certain parts where necessary), go around and tightly fasten each of the screws.
•
If necessary, spread out a blanket or similar material to prevent the stand or floor from being scratched during assembly.
•
Be careful not to pinch the pedal cord during assembly.
Screw “a”
(2 screws)
Screw “a”
(2 screws)
Leave the pedal
cord extended
Improper
Space
Side
board
Side
board
Correct
Pedal
board
Pedal
board
Space
3 mm
Screw “b” (4 pieces)
Screws you loosened
in step 4 (2 screws)
Rear view
1.
Align the screws on the bottom of the piano (one each at left and right)
with the metal brackets on the side boards, and while keeping the front
of the piano slightly raised, pull it toward yourself to engage the screws
in the metal brackets.
* When handling the piano, firmly grasp it. Be careful, so you do not
get your fingers pinched.
2.
Fasten the piano to the stand with the screw “b” (M5 x 20
mm).
fig.2-1.eps
1.
Connect the pedal cord to the Pedal connector.
ˆ
* Plug the pedal cord all the way into the Pedal connector.
Models with a power cord
1.
Connect the included power cord to the AC In jack located on the piano’s
bottom panel.
2.
Plug the power cord into an AC outlet.
Models with an AC adaptor
1.
Connect the supplied AC adaptor and AC cord.
2.
Connect the AC adaptor to the DC In jack on the rear panel.
3.
Plug the power cord into an AC outlet.
As needed, use the plastic-coated clips on the bottom of the piano to
secure the power cord and pedal cord.
Turn the adjuster to lower it until the adjuster is in firm contact with the
floor. In particular, when you’ve placed the piano on carpet, you must
turn the adjuster until it is pressing firmly against the floor.
* The pedal may be damaged if there is a gap between the adjuster
and the floor.
fig.5-1.eps
1.
Close the keyboard lid.
2.
Disconnect the power cord or AC adaptor.
3.
Raise the stand’s adjuster.
4.
Keep the piano level when you lift it, and take care not to pinch your
hands or drop the piano on your feet.
5.
After placing the piano in its new location, perform steps
–
of
the “Assembly Procedure.”
Copyright© 2009 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in
any form without the written permission of ROLAND CORPORATION.
2
Install the piano onto the stand
3
Connecting the pedal cord
4
Connecting the power cord
Screw “b”
Please don’t get your
fingers pinched.
Pull the piano toward yourself while
keeping the front slightly raised.
Power cord
5
Fastening the cords
6
Adjusting the adjuster
Rear view
AC adaptor cord
Coated clip
Adjuster
When Moving the Piano
4
6
Be sure to keep this leaflet together with the owner’s manual.
KSC-54/56
1
KSC-54_56_l_assemble_e.fm 1 ページ ２００９年１０月１４日 水曜日 午前１０時３７分
