Roland JUPITER-X, Руководство пользователя

Страница: 23 / 26

23
Returning to the Factory Settings
(Factory Reset)
Here’s how the settings that you edited and saved on the JUPITER-X
can be returned to their factory-set condition.
* When you execute this operation, all saved settings including the sound
parameters will be lost.
* If you will later need the current settings, be sure to use the backup
function (p. 22) to save the current settings before you restore the
factory settings.
1.
Press the [MENU] button .
2.
Use the [1] knob to select “UTILITY,” and then press the
[ENTER] button .
You can also make this selection by using the PAGE [ ] [ ] buttons
instead of the [1] knob .
3.
Use the [1] knob to select “FACTORY RESET,” and then press
the [ENTER] button .
A confirmation message appears.
If you decide to cancel, press the
[EXIT] button .
4.
To execute, use the [2] knob to select “OK,” and then press
the [ENTER] button .
The display indicates “Completed.”
5.
Turn the power of the JUPITER-X off and then on again.
* Never turn off the power or disconnect the USB flash drive during a
process, such as while the “Executing…” display is shown.
Saving the System Settings
(System)
1.
Press the [MENU] button .
2.
Use the [1] knob to select “SYSTEM,” and then press the
[ENTER] button .
You can also make this selection by using the PAGE [ ] [ ] buttons
instead of the [1] knob .
3.
Use the [1] knob to select the parameter and use the [2]
knob to change the setting.
Saving the System Settings
(System Write)
1.
In the system setting screen, press the [WRITE] button .
A confirmation message appears.
If you decide to cancel, press the
[EXIT] button .
2.
To execute, press the [ENTER] button .
Settings for the Entire Unit
System parameter list
Parameter
[1] knob
Value
[2] knob
Explanation
AGING
Warm-Up
OFF, ON, FAST,
FIXED
Specifies whether the character of the sound
(pitch variance) changes according to the
varying internal temperature of this unit.
This has an effect only on analog synthesizer
models.
The internal temperature value is shown in the
upper right of the top screen of the scene.
OFF:
The character of the sound is not affected
by the temperature. Nor is there a temperature
indication in the SCENE screen.
ON:
The internal temperature starts at the
value specified by Aging Init Temp, and
changes to the actual temperature (REAL).
Although it depends on the temperature
difference, the REAL temperature is reached
in approximately ten minutes. After reaching
the REAL temperature, the setting follows the
actual temperature change.
FAST: The internal temperature starts at
the value specified by Aging Init Temp, and
then quickly (in approximately ten seconds)
changes to the actual temperature (REAL)
when you play the keyboard. After reaching
the REAL temperature, the setting follows the
actual temperature change.
FIXED: The internal temperature is fixed at the
value specified by Aging Init Temp, and the
character of the sound is maintained at that
point.
Init Temp
REAL,
0–60 [°C]/
32–140 [°F]
Specifies the initial internal temperature for
Warm-Up.
REAL: The internal temperature that is actually
measured will be the initial temperature.
0–60°C/32–140°F:
Virtually specifies the initial
internal temperature (Centigrade/Fahrenheit).
Age
OFF,
1–100 [years]
Simulates the aging of an analog synthesizer’s
internal components. Increasing this value
changes the sound as it would be on a unit
that is a corresponding number of years old.
This is valid only for sounds of an analog
synthesizer model.
GENERAL
MasterTune
415.3–466.2 [Hz]
Adjusts the overall tuning.
The displayed value is the frequency of the A4
key (middle A).
MasKeyShift -24–24
Shifts the JUPITER-X’s overall pitch range in
semitone steps.
ScaleTuneSw OFF, ON
Specifies whether the scene’s SCALE TUNE
setting is enabled (ON) or disabled (OFF).
USB In Lev 0–127
Adjusts the audio input level of the USB
COMPUTER port.
USB Out Lev 0–127
Adjusts the audio output level to the USB
COMPUTER port.
AuxIn/BT InLev
0–127 Adjusts the input level of the AUX IN jack.
USB Audio Thru
OFF, ON
Specifies whether the audio input of the USB
COMPUTER port is mixed into the audio output
of the USB COMPUTER port.
If you don’t want to output this audio, turn
this “OFF.”
AUXIN USB Thru
OFF, ON
Specifies whether the input of the AUX IN
jack is mixed into the audio output of the USB
COMPUTER port.
If you don’t want to output this audio, turn
this “OFF.”
Line Out Gain
-12–0–+12 [dB] Adjusts the output gain of OUTPUT/PHONES.
Speaker Sw
OFF, ON, AUTO
Specifies whether sound is output from the
speakers. The AUTO setting operates as “OFF”
when headphones are connected and as “ON”
when headphones are not connected.