Appendix
24
Main Specifications
Roland S-2416: STAGE UNIT
Number of Channels
32 in 24 out
AD Conversion
Sample Rate: 96.0 kHz, 48 kHz, 44.1 kHz
Signal Processing: 24 bits
DA Conversion
Sample Rate: 96.0 kHz, 48 kHz, 44.1 kHz
Signal Processing: 24 bits
Frequency Response
-2 dB / +0 dB (@ +4 dBu, 20 Hz to 40 kHz, Sample Rate: 96 kHz, typ.)
-2 dB / +0 dB (@ +4 dBu, 20 Hz to 20 kHz, Sample Rate: 48 kHz / 44.1 kHz, typ.)
Total Harmonic Dist Noise
0.007 % (Pad: Off, Input Gain: -10 dBu, 20 Hz–20 kHz, typ.)
Dynamic Range
INPUT jacks (1–24): 110 dB (typ.)
Channel Separation (1 kHz)
INPUT jacks (1–24): 103 dB (Input Gain: +4 dBu, IHF-A, typ.)
OUTPUT jacks (1–16): 110 dB (typ.)
Nominal Input Level (Variable)
-65–-10 dBu (PAD: Off)
-45–+10 dBu (PAD: On)
Non Clip Maximum Input Level
INPUT jacks (1–24): +28 dBu (1 kHz, 10 kΩ load, typ.)
Input Impedance
INPUT jacks (1–24): 7 kΩ
Nominal Output Level
OUTPUT jacks (1–16): +4 dBu (Load impedance: 10 kΩ, typ.)
Maximum Output Level
OUTPUT jacks (1–16): +22 dBu (Load impedance: 10 kΩ, typ.)
Output Impedance
OUTPUT jacks (1–16): 600 Ω (typ.)
Recommended Load Impedance
OUTPUT jacks (1–16): 10 kΩ or greater
Residual Noise Level (IHF-A, typ.)
OUTPUT jacks (1–16): -84 dBu
Equivalent Input Noise Level (E.I.N.)
INPUT jacks (1–24): -128 dB (Input Gain: -65 dBu, IHF-A, typ.)
Network Latency
375 µs when using REAC cable only (AD to REAC to DA Latency: about 1.2 ms) *1
Connectors
INPUT jacks (1–24):
XLR type, balanced, phantom power
OUTPUT jacks (1–16):
XLR type, balanced
AES/EBU connector:
DB-25 type
REAC port:
RJ-45 EtherCon type
WORD CLOCK connector: BNC type
REMOTE connector:
DB-9 type
COMPUTER port:
USB type B
* XLR type: 1 GND, 2 HOT, 3 COLD
* Phantom power: DC +48 V (unloaded maximum), 14 mA (maximum load) (All XLR type inputs)
Power Consumption
62 W
Dimensions
482 (W) x 348 (D) x 177 (H) mm
19 (W) x 13-3/4 (D) x 7 (H) inches
(EIA-4U rack mountable)
Weight
9.7 kg
21 lbs 7 oz
Operation Temperature
+0–+40 degrees Celsius
+32–+104 degrees Fahrenheit
Accessories
Power cord
Owner’s manual
Rubber foot x 4
*1 When a REAC Splitter S-4000D or a switching hub is used in-line with REAC cables, the network latency will increase by the amount of processing delay introduced
by the splitting device itself. The actual delay is dependant upon the specifications of the splitting device, though the maximum delay amount for a single splitting
device should be about 200 µs.
* 0 dBu = 0.775 Vrms
* In the interest of product improvement, the specifications and/or appearance of this unit are subject to change without prior notice.
