Rohde & Schwarz TS-PIO2 страница 39 Скачать руководство пользователя | Manualshive

Страница: 39 / 66

background image

Function Description

R&S

®

TS-PIO2

23

User Manual 1506.7208.12 ─ 06

Figure 5-10: Ground relay

The module is operated ground-free in its basic state. This state can be changed using
the function

rspio2_ConfigureGround

.

Please note that function

rspio2_DisconnectAll

does not open the ground relays!

For technical reasons, a non-switched R&S TS-PIO2 module (no connection of signals
to the front side connector or analog bus) is automatically grounded through the
ground relay. This relay is automatically opened again before new switching is per-
formed. This applies if the R&S TS-PIO2 module is configured groundfree.

5.1.4 Using sense lines

To compensate for voltage drops in the power supply to the external load, the exten-
ded channels (CH4, CH8, CH12 and CH16) of R&S TS-PIO2 can be set to external
sensing. Two additional lines directly to the test object are required for this purpose.
The measured difference in voltage on these lines is automatically controlled to the tar-
get voltage by R&S TS-PIO2.

The sense lines on the front side connector (CHx_SHI und CHx_SLO) are switched
using function

rspio2_ConfigureRemoteSensing

.

5.1.5 Adjusting current limiting

The extended channels (CH4, CH8, CH12 and CH16) of the R&S TS-PIO2 make it
possible to adjust current limiting. The set value is independent of the mode of a chan-

Function description of the R&S TS-PIO2 module

«
...
37
38
39
40
41
...
»

Содержание TS-PIO2



































































Отзывы:

Нет отзывов

Похожие инструкции для TS-PIO2

Бренд: Aiphone Страницы: 2

Бренд: Serene Страницы: 48

Бренд: Aiphone Страницы: 4

tyco AQUAMIST ULF AM33

Бренд: Johnson Controls Страницы: 4

HOF14AFRQ 1F Series

Бренд: Halsey Taylor Страницы: 4

Бренд: Toa Страницы: 1

Hy-Brid 3 Series

Бренд: Custom Equipment Страницы: 23

The One MP-TO-01-C

Бренд: Meet PAT Страницы: 14

Бренд: BAS-IP Страницы: 59

ZIP CHAIN LIFTER

Бренд: Tsubaki Страницы: 40

Бренд: FOUR Страницы: 28

Бренд: Kraken Acoustics Страницы: 12

Бренд: CarlStahl Страницы: 28

Бренд: B&R Industries Страницы: 2720

Бренд: RTS Страницы: 28

Бренд: AAT Страницы: 32

Alltech 3300 ELSD

Бренд: DataApex Страницы: 20

Бренд: morse Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды