Rohde & Schwarz TS-PIO2 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 66

Rohde & Schwarz TS-PIO2 Скачать руководство пользователя страница 43

Function Description

R&S

®

TS-PIO2

27

User Manual 1506.7208.12 ─ 06

Table 5-3: Methods for voltage measurement

Method

Note

Single Ended

The level is measured between one input (CHx_IN) and module ground (AGND
or LO on the front side connector)

Differential

The level between two inputs is determined by taking the difference. The follow-
ing combinations of inputs are possible:

CH1 - CH9

CH2 - CH10

CH3 - CH11

CH4 - CH12

CH5 - CH13

CH6 - CH14

CH7 - CH15

CH8 - CH16

The following measurement ranges can be set:

●

7V

●

14V

●

28V

Voltage measurement can be configured with function

rspio2_ConfigureAnalogMeasurement

.

Recording of measurement values is monitored by sequence control (see Section
5.1.13). The setting of the the time interval also determines the conversion time of the
ADC and thus the input bandwith and accuracy that can be achieved. Because of this,
parameter „Sample Interval“ of function

rspio2_ConfigureSampling

is meaningful

even if only one measurement value („Sample Count“ = 1) will be recorded!

Table 5-4: Effect of „Sample Interval“ on bandwidth and accuracy

Interval

Input Bandwidth

Accuracy

200

μ

s <= Sample Interval < 1 ms

High

Lower

1 ms <= Sample Interval < 10.0 ms

Medium

Higher

10.0 ms <= Sample Interval <= 1 s

Low

Best

Recording of measurement values is started by sequence control (see Section 5.1.13).
The results can be queried with function

rspio2_FetchAnalog

. If you are only inter-

ested in the average value of all the samples recorded, it can be retrieved with

rspio2_FetchAverage

.

5.1.13 Triggering and sequence control

Measurement values are recorded and output of digital bit patterns is monitored by a
central control system. Function

rspio2_ConfigureSampling

can be used to

define the number of „Samples“ that will be recorded or generated. The time interval
between the „Samples“ can be adjusted with this function.

Function description of the R&S TS-PIO2 module

«
...
41
42
43
44
45
...
»

Содержание TS-PIO2



































































Отзывы:

Нет отзывов