manualshive.com logo in svg

Rohde & Schwarz 1803.7000K04, Начало работы, Страница: 23 / 79

Поделиться
Скачать
Rohde & Schwarz 1803.7000K04 Скачать руководство пользователя страница 23

Preparing for use

R&S

®

RTP

23

Getting Started 1803.6478.02 ─ 01

2. Plug the AC power cable into a power outlet with ground contact.

The required ratings are listed next to the AC power connector and in the data
sheet.

4.7

 

Switching on or off

The instrument is switched on or off with the power switch and the [Power] key.
The [Power] key is located in the bottom left corner of the front panel. The power
switch is located at the rear panel of the instrument.

Table 4-1: Overview of power states

Status

LED

Power switch

Off

 (unlighted)

[0] (off)

Standby

 orange

[I] (on)

Ready

 green

[I] (on)

To switch on the product

The product is off but connected to power.

1. Set the switch on the power supply to position [I].

The power key on the front panel lights up.

2. Press the [Power] key on the front panel.

The instrument performs a system check, boots the operating system, and
then starts the R&S

 

RTP firmware.

The [Power] key turns green and the illuminated keys on the front panel light
up. If the previous session was terminated regularly, the oscilloscope uses the
last settings.

Before you start measurements, be sure to comply with the warm-up phase
specified in the data sheet.

To shut down the product

The product is in the ready state.

► Press the [Power] key.

Switching on or off

Содержание 1803.7000K04
















































































Отзывы:

Нет отзывов