CE-41
Plus
P/N 121-500-0746
PRODUCT DESCRIPTION
This device, P/N 121-500-0746, is used to control
the vibration level a vibratory feeder. The unit is
powered from the incoming line connection. The
unit has its own Master Control PC board. The
setup and operation is detailed in the following
product literature.
SPECIFICATIONS
Line
Voltage:
120
VAC
+/-10%
Line
Frequency:
50/60
Hz
Current:
15A
Output
Voltage:
0-120
VAC
Handling & Transp. Temp.
-40 – 60
C
Operating Temp.
0 – 40
C
INSTALLATION
The control is to be firmly mounted to a non-
vibrating surface. The control is designed to
withstand conditions equal to IP54. Do not install
the control in a more severe environment.
Connections to external conduits or cords are to
be made with hardware that is rated at IP54 or
better.
Refer to the electrical wiring diagram. Line and
load wiring is to be brought into the box via
customer-drilled holes. Use 2.5mm
2
(#14 AWG)
Mains supply wires or larger. Use 2.5mm
2
(#14AWG) load wires or larger. The Mains supply
wires should be fused by the Customer at 15 amps
or less. After the wiring has been completed,
verify the continuity of the ground bond connection
to the control.
This control is for industrial use. Use in residential
areas may cause interference, and in that case,
special measures may have to be taken by the
user regarding emissions.
IMPORTANT - The vibratory feeder must be
tuned to match the power line frequency of the
destination country (50 or 60 Hz). A feeder
tuned to the wrong frequency will not feed
parts. The Rodix control operates on 50 or 60
Hz.
SAFETY
When installing this control, a power supply
disconnect device must be provided by the user.
A power plug/socket combination can be utilized
for this purpose. The plug and socket must have a
breaking capacity of at least the amperage of the
vibratory feeder(s).
©
2006
Hazard Communication Systems, LLC
Figure 1 – Warning label installed on the control
Warning – There is hazardous voltage inside
the control. Disconnect power before opening
the enclosure.
Only skilled or instructed persons
should open the enclosure.
An electrically instructed person is a person
adequately advised or supervised by an electrically
skilled person to enable him or her to perceive
risks and to avoid hazards which electricity can
create.
An Emergency stop device must be installed on
the machine that incorporates the CE feeder
control.
When the machine is installed, verify the continuity
of the protective bonding circuit (earth ground) to
the control.
PERIODIC INSPECTION AND
FUNCTIONAL TESTING
When the control is operating normally, the output
can be smoothly adjusted from zero to maximum
by the main control knob. If part sensors are used,
the control starts and stops automatically
according to the time delay settings on the circuit
board. If soft-start is used, the output should start
at zero and ramp up to the desired setting each
time the control automatically starts.
The control should be kept reasonably free from
dirt and contaminants that might inhibit proper
cooling. No other planned maintenance is
necessary.
MAINTENANCE
Normally no maintenance is needed for this
control. If troubleshooting assistance is needed,
either visit our web site at
www.rodix.com
, call
RODIX: (international call) 815-316-4700x322 or
(USA) 1-800-562-1868x322, FAX: 815-316-4701,
or e-mail:
.
SPARE PARTS
Designation
Q Rodix P/N MFG P/N
Control Card
1 123-293*
Fuse 15A 250V 1 106-18*
Bussman
ABC15
OR
Littlefuse
314015
Fuse Holder 1 106-17
Littlefuse
354901GY
Triac
1 115-32*
S1 (DPST) 1 104-80*
Switch Boot
1 104-26*
Term. End
264-301 Wago
20A, 600V 264-301
Terminal Single 264-321 Wago
20A, 600V 264-321
Terminal Dual 264-351 Wago
20A, 600V 264-351
Knob
122-01 APEM
MPKES120B1/4
*Recommended spare parts to keep in stock.
© 2000, 2015 RODIX
INC
.
CE-41 Plus 24-211 4/21/2014 Page 1
RODIX INC.
FEEDER CUBE
CE-40
Plus Series
