19
Operating instructions
For correct operation of the mixing panel, please follow the instructions below.
1) Before connecting anything to the mixing panel, be sure all equipment is turned off. Then
connect the different audio sources, amplifiers, effects-units, headphones, etc.. Next step is to
turn on the audio sources and effects-units.
When all these units are in ready state, you can switch on the power switch (A) of the mixing
panel. The power indicators (18) will light up.
After 5 seconds, you can turn on the loudspeaker processors and amplifiers.
R
R
R
L
L
L
ACTIVE BOOTH
MONITORS
POWER
AMPLIFIER
LOUDSPEAKER
PROCESSOR
TO SECONDARY
SPEAKERS
TO MAIN
AMPLIFIERS
R
R
L
L
EFFECTS MACHINE
EFFECTS MACHINE
RODEC
f i l t e r t e c h n o l o g y i n s i d e
RE
RODEC
f i l t e r t e c h n o l o g y i n s i d e
RE
HEADPHONES
R
L
FLASH-CARD
PLAYER
FIRE ALARM
CENTRAL
DJ
MICROPHONE
REVERB
PROCESSOR
MASS STORAGE
PLAYER
PC BASED MUSIC
PLAYER/RECORDER
R
L
PHONO
TURNTABLE
R
L
PHONO
TURNTABLE
R
R
L
L
PROFESSIONAL
DOUBLE CD PLAYER
DAB RECIEVER
R
L
SUB MIXER
+
-
0
+
-
0
M AX
0
M AX
0
M AX
0
M AX
0
M AX
0
M AX
0
PHO NO 2
ST RAI GHT
REVERSE
SEL ECT
L EVEL
LINE 2
PHO NO 1
M IC 3
L INE 1
LINE 3
BALANC E
M ID
HIGH
LO W
BAL ANC E
FX-IN SERT
F X- IN SERT
L
WET
DRY
F X- IN SERT M I X
R
PF L
CH 1-2
M ON O
M OD E
PF L M IX
M ASTER
2
M ASTER
1
-3
-5
PO WER
-2 0
-1 0
0
-
+
-1
0 dB
0dB
+ 5
+ 3
+ 1
C HA N N EL 2
IN PU T 1
IN PU T 2
L EVEL
LEVEL
IN PUT
SEL ECT
LEVEL
EQ HIG H
EQ LO W
PF L
RO UT IN G
M ID
HIGH
LO W
OU TPU TS
0
-
+
0
-
+
EQ UAL IZ ER
EQ UAL IZ ER
SESS IO N /
AU X IN
C HA N N EL 3
M IX L /CH 1
M IX R/C H2
VU
SELECT
CH 1
CH 2
0
-
+
RO UT IN G
M IX
CH 1
CH 2
C H AN N EL 1
SELECT
L
R
RODEC
CU T
CU T
CH 2
PF L C H1 - CH2 SEL ECT
CH 1
NO RM AL
NO RM AL
REVERSE
REVERSE
R
L
SAMPLER
R
L
DVD-PLAYER
www.rodec.com
RODEC
Made in Belgium
Professional
Audio Equipment
WARNING
DISCONNECT POWERCORD
BEFORE OPENING
P S
E
2) Connect the headphones to the headphones JACK connector (31) or (L). Use headphones with
impedance between 32 and 600
Ω
.
ATTENTION!
Always turn headphones volume to “0” (fully counter clockwise)
BEFORE
putting the headphones on your or somebody else her/his ears! Then slowly
raise the volume by turning the volume knob in clockwise direction.
3) Choose with the input select switch (1) the right audio-source.
4) Switch the PFL button (8) in position ON to listen at the desired source. Turn the phones select
button (29) completely to the left and turn the phones volume potentiometer (30) to the desired
position to get the stereo signal on the headphones and the two left VU-meters. The PFL circuit
works as a sum-system, there is a possibility to listen to more sources at the same time. All
these operations have no influence on the output signal! Adjust with the level control (2) the
input signal until the red indicators of the level meters (13) will light up occasionally. Adjust if
necessary the quality of the sound with the equalizer (3).