Rockwell RK7241S, Руководство пользователя

Страница: 11 / 56

11
Jobsite table saw with laser eNG
b. For all Double-iNsulateD tools
1. replacement parts
When servicing use only identical replacement
parts.
2. Polarized Plugs
To reduce the risk of electric shock, this equipment
has a polarized plug (one blade is wider than the
other). This plug will fit in a polarized outlet only
one way. if the plug does not fit fully in the outlet,
reverse the plug. if it still does not fit, contact a
qualified electrician to install the proper outlet. do
not change the plug in any way.
C. For all tools as aPPliCable
1. KeeP GuarDs iN PlaCe
and in working order.
2. reMoVe aDJustiNG KeYs aND wreNChes.
form habit of checking to see that keys and
adjusting wrenches are removed from tool before
turning it on.
3. KeeP worK area CleaN.
Cluttered areas and
benches invite accidents.
4. DoN’t use iN DaNGerous eNViroNMeNt.
don’t
use power tools in damp or wet locations, or expose
them to rain. Keep work area well lighted.
5. KeeP ChilDreN awaY. all visitors should be kept
at a safe distance from work area.
6. MaKe worKshoP KiD ProoF
with padlocks,
master switches, or by removing starter keys.
7. DoN’t ForCe tool.
it will do the job better and
safer at the rate for which it was designed.
8. use riGht tool.
don’t force tool or attachment to
do a job for which it was not designed.
9. use ProPer eXteNsioN CorD. Make sure your
extension cord is in good condition. When using an
extension cord, be sure to use one heavy enough
to carry the current your product will draw. an
undersized cord will cause a drop in line voltage
resulting in loss of power and overheating. Table
1 shows the correct size to use depending on cord
length and nameplate ampere rating. if in doubt, use
the next heavier gage. The smaller the gage number,
the heavier the cord.
10. wear ProPer aPParel.
do not wear loose
clothing, gloves, neckties, rings, bracelets, or other
jewelry which may get caught in moving parts.
Nonslip footwear is recommended. Wear protective
hair covering to contain long hair.
11. alwaYs use saFetY Glasses.
also use face
or dust mask if cutting operation is dusty. Everyday
eyeglasses only have impact resistant lenses, they
are NOT safety glasses.
12. seCure worK.
use clamps or a vise to hold work
when practical. it’s safer than using your hand and it
frees both hands to operate tool.
13. DoN’t oVerreaCh.
Keep proper footing and
balance at all times.
14. MaiNtaiN tools with Care.
Keep tools
sharp and clean for best and safest performance.
follow instructions for lubricating and changing
accessories.
15. DisCoNNeCt tools
before servicing; when
changing accessories, such as blades, bits, cutters,
and the like.
16. reDuCe the risK oF uNiNteNtioNal
startiNG.
Make sure switch is in off position
before plugging in.
17. use reCoMMeNDeD aCCessories.
Consult the
owner’s manual for recommended accessories. The
use of improper accessories may cause risk of injury
to persons.
18. NeVer staND oN tool. serious injury could
occur if the tool is tipped or if the cutting tool is
unintentionally contacted.
19. CheCK DaMaGeD Parts.
before further use
of the tool, a guard or other part that is damaged
should be carefully checked to determine that it will
operate properly and perform its intended function
– check for alignment of moving parts, binding of
moving parts, breakage of parts, mounting, and
any other conditions that may affect its operation.
a guard or other part that is damaged should be
properly repaired or replaced.
20. DireCtioN oF FeeD.
feed work into a blade or
cutter against the direction of rotation of the blade
or cutter only.
21. NeVer leaVe tool ruNNiNG uNatteNDeD.
turN Power oFF.
don’t leave tool until it comes
to a complete stop.