Rockwell RK2511, Руководство по эксплуатации

Страница: 8 / 24

8
12V CORDLESS SCREWDRIVER ENG
speed and torque with increased trigger pressure.
Speed is controlled by the amount of switch trigger
depression.
WARNING: Do not operate for long periods at low
speed because excess heat will be produced
internally.
3. SWItCh LOCK
The switch trigger can be locked in the OFF position.
This helps to reduce the possibility of accidental
starting when not in use. To lock the switch trigger,
place the rotation control in the center position.
4. fORWARD/REVERSE SWItCh (SEE C)
For drilling and screw driving use forward rotation
marked “ ” (lever is moved to the left). Only use
reverse rotation marked “ ” (lever is moved to the
right) to remove screws or release a jammed drill bit.
WARNING: Never change the direction of
rotation when the chuck is rotating, wait until it
has stopped !
5. tWO-SPEED GEAR CONtROL (SEE D)
The screwdriver has a two-speed gear control designed
for drilling or driving at LO (mark is 1) or HI (mark
is 2) speeds. A slide switch is located on top of the
screwdriver to select either LO or HI speed. When
using the screwdriver in the LO speed range, the speed
will decrease and the drill will have greater power and
torque. When using the screwdriver in the HI speed
range, the speed will increase and the screwdriver will
have less power and torque.
Gear I
Low speed range: for screwdriving or working with
large drilling diameter
Gear II
High speed range: for working with small drilling
diameter
WARNING: To prevent gear damage, always
allow the chuck to come to a complete stop
before changing the direction of rotation or the two-
speed gear control.
6. tORquE ADjuStmENt (SEE E)
The torque is adjusted by rotating the torque
adjustment ring. The torque is greater when the torque
adjustment ring is set on a higher setting. The torque is
less when the torque adjustment ring is set on a lower
setting.
Make the setting as follows:
1 - 4 for driving small screws
5 - 9 for driving screws into soft material
10 - 15 for driving screws into soft and hard material
for heavy drilling
7. fuLLy AutOmAtIC SPINDLE LOCKING (AutO-LOCK)
(SEE f)
The screwdriver chuck (1) is locked when the on/off
switch (8) is not pressed.
This enables screws to be screwed in, even when the
battery is empty and allows for the machine to be used
as a manual screwdriver.
ImPORtANt:
When using as a manual tool, do not press the On/Off
switch (8). Otherwise the screwdriver can be damaged.
8. uSING thE LED LIGht
The sight light allows you to keep a clear view under
less illuminated circumstances. To turn on the light
simply press the on/off switch. When you release the
on/off switch, the light will be off.
LED is also a battery capacity indicator. It will flash
when power gets low.
9. DISPOSAL Of AN EXhAuStED bAttERy PACK
To preserve natural resources, please recycle
or dispose of the battery pack properly. This
battery pack contains Lithium batteries. Consult
your local waste authority for information regarding
available recycling and/or disposal options. Discharge
your battery pack by operating your tool, then remove
the battery pack from the tool housing and cover the
battery pack connections with heavy-duty adhesive
tape to prevent short circuit and energy discharge. Do
not attempt to open or remove any of the components.
PRObLEm SOLutION
1. Why DOES thE SCREWDRIVER NOt tuRN ON WhEN yOu
PRESS thE SWItCh?
The forward/reverse rotation control, which is on top
of the trigger, is positioned in the lock function. Unlock
the forward/reverse rotation control by putting it into
the required rotation position. Push the trigger and the
screwdriver will start to rotate.