background image

10000229312

00

G. FILLUS

12-22-11

6

12

B

210mm W  x  297mm H

8 - 1/2" W  x  11" H

CUT SIZE

This guide is designed to get the user quickly interfacing with the 855H Recordable Horn.

Switch

No.

1

2

3

4

5

6

7

855H RECORDABLE HORN QUICK START GUIDE

The unit can be set-up to either play an alarm tone followed by a recorded message, or

just play the recorded message. 
The user can: 

o

Record on each of the 4 stages using either the Line-in or Microphone inputs

o

Select the required alarm tone for each stage

o

Delete unwanted messages.

To re-record a message on a particular stage, the previous message on that stage must

be deleted first.

The “Mass Erase” function will erase all the recorded stages and also reset the unit.

Once the user has configured the unit, it must be put into its Playback Mode and S2

switches set to stage 1, as shown in Quick Ref - Playback Mode (Stage 1 illustrated)

guide below. 

OFF Position Function

Record Mode 

Stage selection switch

Stage selection switch

Audio Line-In selected 

Program  (Record &

Erase Mode ON)

Message & Tone

Playback

Single Message or Mass

Erase Mode OFF

SWITCH S2 (SET-UP) FUNCTION SETTINGS

(NOTE: “Black” color indicates “ON” position)

ON Position Function

Playback Mode

Switch 2 On & Switch 3 On = Alarm Stage 1

Switch 2 Off & Switch 3 On = Alarm Stage 2

Switch 2 On & Switch 3 Off = Alarm Stage 3

Switch 2 Off & Switch 3 Off = Alarm Stage 4

On board Microphone selected

Playback (Record & Erase Mode OFF)

Message only Playback

Single Message or Mass Erase Mode ON

6

              INSTRUCTION SHEET
                   FOR BUL. 855H
      RECORDABLE HORN FRAME E

Содержание 855H-R30E













Отзывы: