Rockwell Automation 1738-AENTR Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 24

Rockwell Automation 1738-AENTR Скачать руководство пользователя страница 4

4

ArmorPoint I/O 2-Port EtherNet/IP Adapter, Series A

Publication

1738-IN028B-EN-E - February 2010

About the Module

The ArmorPoint I/O 2-Port EtherNet/IP adapter provides connectivity to
an EtherNet/IP network via two M12 Ethernet-keyed connectors for 2-port
pass-through to support daisy chains or rings, and the existing star and tree
network topologies.
The adapter ships with a terminating base to be used with the last I/O
module on the backplane. The sealed IP67 housing of the adapter requires no
enclosure. (Note that environmental requirements other than IP67 may
require an additional appropriate housing.) The EtherNet/IP connector is a
sealed D-coded M12 (micro) style.

ATTENTION

Make sure all connectors and caps are securely tightened to properly seal the
connections against leaks and maintain IP enclosure type requirements.

ATTENTION

To comply with the CE Low Voltage Directive (LVD), all connected I/O must be
powered from a source compliant with the following:
Safety Extra Low Voltage (SELV) or Protected Extra Low Voltage (PELV).

«
...
2
3
4
5
6
...
»

Содержание 1738-AENTR

























Отзывы:

Нет отзывов