manualshive.com logo in svg

Rockwell Automation 1738-AENTR, Руководство по установке, Страница: 11 / 24

Поделиться
Скачать
Rockwell Automation 1738-AENTR Скачать руководство пользователя страница 11

ArmorPoint I/O 2-Port EtherNet/IP Adapter, Series A    

11

Publication

 1738-IN028B-EN-E - February 2010

Interpret the Status Indicators

Adapter Status 

Status

Description

Recommended action

Off

No power applied to device.

Apply power to device.

Green

Device operating normally.

None.

Flashing 
red/green

Device is in self-test.

None.

Flashing red

Recoverable fault has occurred:

 

- Firmware (NVS) update.

 

- Address switches changed.

 

- Complete firmware update.

 

- Verify address switches.

Adapter Status indicator
Network Activity indicator
Network Status indicator

System Power indicator
Adapter Power indicator

PointBus Status indicator

1738-AENTR

EtherNet I/P

Adapter
Status

Network
Activity

Network
Status

PointBus
Status

System
Power

Adapter
Power

conformance tested

™

PWR

IP ADDRESS

Link 2
Activity/
Status

Link 1
Activity/
Status

44830

Link 1 Activity/Status 
indicator

Link 2 Activity/Status 
indicator

Содержание 1738-AENTR

























Отзывы:

Нет отзывов