Rockwell Automation 1738-AENTR Скачать руководство пользователя страница 12

12

    ArmorPoint I/O 2-Port EtherNet/IP Adapter, Series A 

Publication

 1738-IN028B-EN-E - February 2010

Red

Unrecoverable fault has occurred:

 

- self-test failure (Flash checksum 
failure at power up, ramtest failure 
or EEPROM checksum failure at cycle 
power).

 

- firmware fatal error.

Replace device.

Network Activity 

Status

Description

Recommended action

Off

No link established with Port 1 or 
Port 2.

Verify network cabling, and 
correct, as needed.

Green

- Link established with Port 1 and/or 
Port 2 at 100 Mbps.

 

- Link established with Port 1 and 
Port 2. One port at 100 Mbps and one 
port at 10 Mbps.

None.

Flashing 
green

- Transmit or receive activity present 
on Port 1 and/or Port 2 at 100 Mbps.

 

- Transmit or receive activity present 
on Port 1 and/or Port 2. One port at 
100 Mbps and one port at 10 Mbps.

None.

Yellow

Link established with Port 1 and/or 
Port 2 at 10 Mbps.

None.

Flashing 
yellow

Transmit or receive activity present 
Port 1 and/or Port 2 at 10 Mbps.

None.

Adapter Status (Continued)

Status

Description

Recommended action

Содержание 1738-AENTR

























Отзывы: