Rocal HABIT 50 V, Руководство пользователя

Страница: 11 / 52

10
1.1 Technical specifications
1.2 Breakdown of delivery components
(Make sure you have all the components described below in relation to the picture on section II of the ANNEXED document)
1. Fireplace’s body.
2. Heat-resistant spray paint for touch-ups.
3. Fire grate.
4. Heat-resistant glove.
5. Cleaning cloth for metal painted parts
6. Exterior air inlet kit. (Exterior air inlet connector, connector support, tubular joint, 8x screws and 8xnuts)
7. Tool for handling registers and opening door.
8. Envelope with documents: declaration of performance, energy label, specifications, installation and operation manual, and
Guarantee sheet.
9. +T (flue duct of 1.98 meters of Ø150 (Habit 50V +T / Habit 70A +T) | flue duct of 1.98 meters of Ø180 (Habit 80 +T / Habit
100 +T)
10.
Draft limiter
1.3 Diagram of the equipment's measurements
See the ANNEXED document, section I, page 1.
ALL LOCAL STANDARDS, INCLUDING NATIONAL AND EUROPEAN REGULATIONS MUST BE COMPLIED WITH UPON
INSTALLATION OF THE EQUIPMENT.
THE INSTALLATION MUST BE PERFORMED BY A PROFESSIONAL. FAILURE TO COMPLY WITH THIS CLAUSE SHALL
EXONERATE THE MANUFACTURER FROM ANY RESPONSIBILITY.
2.1 Ground. Make sure the ground where the appliance will be placed is able to support the weight of the device. If not, you will need
a load spreading plate for the equitable distribution of the equipment's weight. In case of doubt, please consult a specialist.
2.2 Flue liner. It is mandatory to have a smoke-tight Flue liner going from the connecting point of the base to the outside in observation
of the smoke pipe diameter. The good condition and suitability of this smoke pipe must be certified by a professional and
must also observe the relevant national regulations . This Flue liner should not be shared with other devices (see Table 1.1
Technical specifications). In cases of too much draught, when the duct exceeds 7 meters in length, or the measurement exceeds 20
Pa, the draft must be adjusted. To do this, use the second part of the baffle plate, to install it follow the steps: "D.6" to "D.9" or adjust
Parameter
Model
HABIT 50 V +T HABIT 70 A +T HABIT 80 +T HABIT 100 +T
Minimum - Maximum draught 11-13 Pa 11-13 Pa 11-13 Pa 11-13 Pa
Fuel consumption 2,31 kg/h 2,37 kg/h 2,44 kg/h 3,19 kg/h
Smoke mass flow rate 5,4 g/s 6,6 g/s 6,6 g/s 9,7 g/s
Performance 86,3% 85,3% 85,3% 86,2%
Nominal output 8,7 kW 8,8 kW 9 kW 12,1 kW
Power range 4 – 9 kW 5,5 – 9,5 kW 6,5 – 11,5 kW 7.5 - 13 kW
Average CO concentration at 13% of O
2
0,048 % 0,062 % 0,062 % 0,090%
Average NO
x
concentration at 13% of O
2
102 mg/Nm 3 106 mg/Nm 3 106 mg/Nm 3 101 mg/Nm 3
Average OGC concentration at 13% of O
2
51 mg/Nm 3 51 mg/Nm 3 51 mg/Nm 3 59 mg/Nm 3
Particle concentration at 13% of O
2
13 mg/Nm
3
22,9 mg/Nm
3
22,9 mg/Nm
3
12,1 mg/Nm
3
Medium draft (trial) 8,4 Pa 8,4 Pa 8,4 Pa 11,4 Pa
Net weight 154 kg 160 kg 187 kg 220 kg
Maximum authorized load (fuel) 3 kg 4 kg 4 kg 4 kg
Reload height 200 mm 175 mm 175 mm 175 mm
Logs length 300 mm 400 mm 400 mm 600 mm
Minimum flue height 4000 mm 4000 mm 4000 mm 4000 mm
Ø Flue duct 150 mm 150 mm 180 mm 180 mm
Ø Air inlet 100 mm 100 mm 100 mm 100 mm
Outer fireplace (back) 500 mm 500 mm 500 mm 500 mm
Outer fireplace (sides) 500 mm 500 mm 500 mm 500 mm
Outer fireplace (frontal) 1000 mm 1000 mm 1000 mm 1000 mm
Electrical wiring connection Silicone hose 3*wire of 1.5 mm 2
Fan airflow (unit) 135 m 3 /h
Fan output (unit) 20 W
Average temperature of smoke 220,8ºC 220,8ºC 211,3ºC 196,8ºC
Type of combustion INTERMITENT
Flue liner NOT SHARED
Fuel NATURAL WOOD
Humidity fuel logs 12-20 % - two years under cover
Certification year 2019 2021
Certificate number 1880-CPR-008-007-19 1880-CPR-008-009-19 1880-CPR-001-004-19 1880-CPR-41-21
1. SPECIFICATIONS
2. REQUIREMENTS PRIOR TO INSTALLATION