Robustel GoRuggedR 3000 Скачать руководство пользователя страница 32

Страница: 32 / 83

Robustel GoRugged R3000 User Guide

RT_R3000_UG_v01.01
Confidential

15.03.2013

31 /
82

“Configuration”->”Cellular WAN”->”Network Provider Type”.

Cellular WAN @ Basic

Item

Description

Default

ISP

Input the ISP’s name which will be shown in the selection list of
“Configuration”->”Cellular WAN”->”Network Provider Type”.

Null

APN, Username,
Password, Dialup
No.

All these parameters were provided by the ISP.

Null

3.11

Configuration -> Ethernet

This section allows users to set the Ethernet WAN and LAN parameters.

Eth0/Eth1

Ethernet @ Eth0

Item

Description

Default

Ethernet Interface
Type

Eth0 can work under two different kinds of mode: LAN and WAN.

LAN

Enable Bridge @
LAN Interface

Enable to make Eth0 works under bridge mode with Eth1. Eth0 and Eth1 will
have the same IP address under this mode.

Enable

Address,

NetMask, MTU @
LAN Interface

Set the IP address, netmask and MTU of Eth0/Eth1. These parameters will be
unconfigurable if you enable Bridge.

Null

Multiple

Address @ LAN
Interface

Assign multiple IP addresses for Eth0/Eth1.

Null

Enable

DHCP

Server @ DHCP
Server

Enable to make router can lease IP address to DHCP clients which connect to
Eth0/Eth1.

Enable

IP Pool Start, IP
Pool End @ DHCP
Server

Define the beginning (IP Pool Start) and end (IP Pool End) of the pool of IP
addresses which will lease to DHCP clients.

192.168.0.2/
192.168.0.100

Netmask @ DHCP
Server

Define the netmask which the DHCP clients will obtain from DHCP server.

255.255.255.0

Lease

Time

DHCP Server

Define the time which the client can use the IP address which obtained from
DHCP server.

Primary/Secondary

Define the primary/secondary DNS Server which the DHCP clients will obtain

192.168.0.1/

Содержание GoRuggedR 3000




















































































Результаты поиска

Содержание GoRuggedR 3000

Отзывы:

Похожие инструкции для GoRuggedR 3000

Бренды по названию

Популярные бренды

Robustel GoRuggedR 3000, Руководство пользователя

Результаты поиска

Содержание GoRuggedR 3000

Отзывы:

Похожие инструкции для GoRuggedR 3000

Бренды по названию

Популярные бренды