Robomow MC150 Скачать руководство пользователя страница 9

Страница: 9 / 50

2.3

Operation Method

•

Robomow is a robotic lawnmower designed to mow and maintain your lawn completely by itself.

•

Simple One-Time Setup

- Robomow requires a simple one time setup, which can easily be done by the

consumer. Robomow recognizes the wire using special sensors, and makes sure it always stays inside the

designated area. Essential accessories are supplied with the product.

•

Working Method –

- Robomow

will automatically mow the lawn. It continuously alternates between mowing and charging.

- It independently leaves the Base Station and cuts the lawn.
- Edge Cutting - Unlike other robotic lawn mowers, Robomow is the only robotic

mower that has a special Edge mode, in which it follows the perimeter wire for

complete coverage of the lawn edges. Robomow is the only robotic mower to cut

outside the wheels.

- Search the Base Station - Robomow starts to search for the Base Station when

the battery capacity becomes too low. It does not mow when it is searching for the

Base Station.

- Robomow will then recharge and proceed mowing as needed. It will continue in

mowing until completing the required mowing time for your lawn (based on the

area you have set).

- When completing the mowing of the entire area (Mowing Cycle), Robomow will

stay in the Base Station until the next Mowing Cycle will start.

- Robomow completes two Mowing Cycles per week in order to keep your lawn

healthy and good looking. However if your lawn requires more time to maintain

your lawn, you can easily adjust the time Robomow runs in a single Mowing Cycle.

- The Operating Panel on the top of Robomow is where you manage the mower and

operating settings.

Strong Cutting System - Robomow’s extra sharp blade enables to perform the first

cut of the season, when the grass is relatively high.

- Availability - The mowing width of Robomow (28cm) and the powerful cutting

system help Robomow to finish the job very fast and leave your lawn free for the

family to enjoy.

•

A Remote Control

is available as an accessory and is used for driving Robomow to a separated zone, if

necessary. It is also used for mowing small patches of grass that cannot be reached in automatic operation.

•

Grasscycling

- Robomow cuts the grass into very small clippings that are buried in the roots of the lawn,

where they decompose and act like a natural fertilizer. Grass clippings contain 80-85% water and release

valuable nutrients that return back into the soil. It is the natural recycling of grass.

•

Robomow App

– Enables user friendly and intuitive operation of your

Robomow and opens more menu options and features, which are not

available through the mower Operating Panel. The

Robomow App

can

be downloaded from the Apps Store.
Robomow App is compatible with Smartphones/ Tablets that use one of

the following Operating Systems: Android (Google) or iOS (Apple).
The mobile device has to include

Bluetooth Low Energy

(

BLE

) branded

Bluetooth SMART

The following mobile devices include BLE:

Samsung Galaxy SIII, Galaxy S4 and

Note II.

Apple’s iPhone 4S, iPhone 5, iPad (3rd

& 4th generation), iPad Mini and others.

HTC One, One X+ and Droid DNA

To download the Robomow App, use your

mobile device to scan the QR code on the

right, or download it from the App Store.

LAWN FREE

TO ENJOY

SCAN

HOME

EDGE &

SCAN

STOP

04:26

Scanning

9:41 AM

100%

LAWN FREE

TO ENJOY

Содержание MC150



















































Результаты поиска

Содержание MC150

Отзывы:

Похожие инструкции для MC150

Бренды по названию

Популярные бренды

Robomow MC150, Руководство по эксплуатации

Результаты поиска

Содержание MC150

Отзывы:

Похожие инструкции для MC150

Бренды по названию

Популярные бренды