background image

48

13. 

   

 Tips for maintaining your lawn

Robomow®- Lawn care has never been so easy

Best time to mow

Mow your lawn when the grass is dry. This prevents the clippings from clumping and leaving piles on the lawn. Mow 

it late in the day rather than during the heat of the day.

Mowing frequency

Mow often, producing short, small clippings. During the active growing season the mowing frequency should be 

increased to once every 3-5 days, before the grass is too long. Short clippings decompose quickly and will not 

cover the grass surface. If the grass gets too high, raise the cutting height, mow, then gradually lower it over several 

mowings.

Cutting Height

Follow the “1/3 rule”. Mow no more than 1/3 of the length of the 

grass. Proper mowing will produce short clippings that will not cover 

up the grass surface. 
You may have to cut the lawn more frequently, or double cut, when 

the lawn is growing fast, such as in the spring.

Grasscycling

Grasscycling reduces the amount of water needed by lawns since the clippings are about 80 – 85% water. Grasscycling 

slows evaporation losses from the soil surface, and conserves water. Most lawns need less water when Grasscycling.

Watering

Water your lawn between 4 a.m. and 8 a.m. in the morning, so water has time to soak into the soil before the heat of 

the sun causes evaporation.
Your lawn needs 1 to 1-1/2” (3-4cm) of water weekly. Deep watering allows grass to develop a deep root system, 

enabling the lawn to resist disease and drought.

Do not over water

Too much water is not only wasteful but can also increase turf growth, which requires more frequent mowing. Let the 

soil partially dry out between watering. Water when the top two inches of soil have dried out. Use an object such as 

a screwdriver to probe your soil and measure the depth of the moisture.

Fertilization

Grasscycling reduces the amount of lawn fertilizer needed because the clippings provide about 1/4 of a lawn’s annual 

needs.

Blade

Keep your mower blade sharp. A sharp blade provides a clean, safe, and efficient cut. A dull mower blade will tear 

and shred the tips of the grass, which can provide an entry for disease organisms and weaken the grass plant. It is 

recommended to replace the mower blade once a year.

Thatch

Clippings and thatch are simply not connected. As mentioned previously, grass clippings are approximately 80-85 

percent water with only small amounts of lignin, and decompose rapidly.

When we stop and think about it, golf courses, sports fields, and parks, have been mowing grass for years and 

recycling with no grass catchers.

A small amount of thatch (approximately 1/2 inch) is actually beneficial to a lawn. Grass clippings protect your lawn’s 

root system from heat and water loss.

Содержание MC150



















































Отзывы: