Robin America EH72 Скачать руководство пользователя страница 72

Страница: 72 / 74

– 68 –

Maintenance Items

Every 8

hours

(Daily)

Every

hours

Every

hours

Every

200

hours

Every

500

hours

Every

1000

hours

Clean engine and check bolts and nuts

(Daily)

Check and refill engine oil

(Refill daily

to upper level)

Change engine oil (*Note 1)

(Intial)

Replace engine filter (*Note 1)

(Intial)

Check battery electrolyte fluid level

Clean spark plug

Clean air cleaner

Replace air cleaner element

Clean fuel strainer

Clean and adjust spark plug and electrodes

Replace spark plug

Remove carbon from cylinder head

Clean and adjust carburetor

Clean engine base (oil pan)

Check and adjust valve clearance

Replace fuel lines

(Yearly)

Overhaul engine (*Note 2)

*Note 1 : Initial oil change and oil filter replacement should be performed after 20 hours of operation. Thereafter

change oil every 50 hours and replace oil filter every 200 hours.

Before changing oil, check for a suitable way to dispose of old oil. Do not pour it down into sewage

drains, onto garden soil or into open streams. Your local zoning or environmental regulations will give

you more detailed instructions on proper disposal.

*Note 2 : As to the procedures, please refer to the Service Manual or consult your nearest ROBIN service

dealer.

*Note 3 : More frequent oil changing, oil filter replacement and air cleaner service or replacement may be

necessary depending on operating conditions such as dusty environment, high ambient temperature,

heavy engine loading etc.

Periodic Maintenance Schedue Table

Содержание EH72










































































Результаты поиска

Содержание EH72

Отзывы:

Похожие инструкции для EH72

Бренды по названию

Популярные бренды

Robin America EH72, Руководство по обслуживанию

Результаты поиска

Содержание EH72

Отзывы:

Похожие инструкции для EH72

Бренды по названию

Популярные бренды