Robin America EH72 Скачать руководство пользователя страница 49

Страница: 49 / 74

– 45 –

7. LUBRICATION SYSTEM

OPERATION AND FUNCTION

* Full lubrication system is adopted, in combination with large-size torchoid oil pump and cartridge type oil filter.

* The large-size trochoid type oil pump is driven directly by crankshaft, and delivers pressurized engine oil to

the journal and pin portions of crankshaft, camshaft etc.

* The engine oil in the oil pan is fed through the oil pump filter into oil pump and the engine oil pressure is

adjusted by the relief valve after discharging from oil pump. Through the oil cooler and cartridge type oil

filter, the engine oil is provided onto the rotating portions such as journal and pin portion of crankshaft and

camshaft. The splashed engine oil is provided to the cylinder, piston, cylinder head valve system.

* The by-pass valve is incorporated into the cartridge type oil filter. In case that the oil filter element is

clogged, the engine oil is fed through the by-pass valve into the crankcase oil passage.

OIL PUMP

OIL PUMP FILTER

CRANKSHAFT

OIL FILTER

OIL COOLER

RELIEF VALVE

OIL PRESSURE SWITCH

CAMSHAFT

Fig. 7-1

Содержание EH72










































































Результаты поиска

Содержание EH72

Отзывы:

Похожие инструкции для EH72

Бренды по названию

Популярные бренды

Robin America EH72, Руководство по обслуживанию

Результаты поиска

Содержание EH72

Отзывы:

Похожие инструкции для EH72

Бренды по названию

Популярные бренды