background image

900 SNX

Section A - 1

TECHNICAL FILE

2500W MSR PROFILES

Rob

er

t Juliat r

eser

ve the right t

o change or alt

er an

y of the it

ems detailed on this page

, t

o incr

ease or impr

ov

e man

uf

ac

turing t

echniques without prior notic

e.

robert juliat

  Route de Beaumont  F  60530 Fresnoy-en-Thelle   phone: +33 (0)3.44.26.51.89  -  fax: +33 (0)3.44.26.90.79  -  www.robertjuliat.fr

USER’S INSTRUCTIONS

GENERAL INSTRUCTIONS

1.  Not for residential use.

2.  Only qualified technicians are permitted to service these fixtures.

3.  In addition to the instructions indicated on this page, you must 

adhere to the relevant health and safety requirements of the 
appropriate EU Directives.

4.  This fixture is in compliance with section 17: Lighting appliance 

for theatre stages, television, cinema and photograph studios. 
Standards NF EN 60598-1 and NF EN 60598-2-17.

5.  This fixture is rated as IP20, and is for indoor use only.

FIXTURE
6.  Warning: 

high voltage ignition. Disconnect from the mains before 

any servicing.

7.  Make sure the fixture is correctly mounted on an appropriate 

support.

8.  The protection screens, lenses or U.V. filters must be replaced if there 

is any visual damage which might reduce their performance, for 
example, by cracks or deep scratches.

9.  When hung or flown the fixture must be secured by another hanging 

accessory (such as a safety cable or bond) that is of suitable length.

10. The safety bond or cable must be securely attached at the back of 

the fixture. It must be as short as possible or rolled up as necessary 
to ensure the fixture does not travel any distance should it be 
dislodged.

11. Movable accessories (barn doors, HMI shutters, spill rings etc.) must 

also be secured with a suitable safety cable or bond at the front of 
the fixture.

12. Take into account the weight of both the fixture and the accessories 

when choosing the strength of the attachment point and the safety 
cable or bond.

13. Do not open the lighting fixture when the lamp is on.
14. Both the lamp and lamp housing heat up when powered. Wait until 

the fixture is cold before servicing.

15. Do not tamper with the design of the fixture nor any of its safety 

features.

16. Tighten the electrical mains cable connections regularly. Replace 

mains cable with an identical one if damaged.

17. Use only with correct power supply.

Ventilation

18. Keep well away from flammable material.
19. Do not use outside. Do not cover. Do not permit the fixture to get 

wet.

20. To avoid overheating, do not obstruct air vents.
21. If the fixture has fans, make sure they are working correctly. If fans 

are not working, turn the fixture off immediately and service as 
necessary.

Lamp

22. Use only fully enclosed in the fixture.
23. Never look at the lamp directly.
24. Warning: U.V. rays : Protect your eyes.
25. Check that the lamp voltage corresponds to the mains voltage used. 

Do not use a lamp with power that is an incorrect type or voltage to 
the one that is indicated on the lamp housing or packaging.

26. The lamp must be replaced if it has been damaged or deformed by 

the heat.

27. Use only when bulb is in place.

Cleaning

28. Do not touch the lamp or the mirror with your fingers.
29. Keep optical parts (lens, lamps,…) clean with alcohol.
30. Regularly remove dust from the mirror with a soft and clean rag.
31. If the fixture has filters they must be cleaned frequently.

POWER SUPPLY

32. Disconnect from the mains before any servicing.
33. Mains connection only. Do not connect to an "electronic output" 

(dimmer, static relay...).

34. Do not use outside. Do not cover.
35. The power supply has circuit breakers, which should always be kept 

accessible.

36. There is no maximum distance between the lighting unit and the 

power supply.

37. Check the mains voltage.

PLEASE NOTE 

These products have been built to conform to European standards 
relating to professional lighting equipment. Any modification made to 
our products will void the manufacturers' warranty

 

 

Please read carefully all the instructions before operating the appliance.

Danger

The discharge lamp used emits short-wave ultraviolet 

radiation which is harmful to skin and eyes.

Содержание D'ARTAGNAN 900 SNX


























Отзывы: