manualshive.com logo in svg

Robe Color Wash 700E AT, Руководство пользователя

Поделиться
Скачать
Robe Color Wash 700E AT Скачать руководство пользователя страница 8

8

4.5 Changing the front lens 

The ColorWash 700E AT is supplied with the front Fresnel lens installed as standard.

If you wish to install a front wide-angle lens (optional),follow the instructions:

Switch the device off before changing the lens.Be careful.Front lens is heavy!

Changing the front Fresnel lens:

1.Remove the front lens using a flathead screwdriver to unlock the four quarter-turn screws.

.Unscrew the safety cabel from the lens

3.Screw up the safety cable to the wide-angle lens.

4.Place this lens and fix it by locking the four quarter-turn screws.

4.6 Installing top hats 

The ColorWash 700E AT can be fitted with various types of the top hats-see chapter "Technical specifications".If 

you wish to install a top hat (optional),follow the instructions:

Switch the device off before installing the top hat!

Installing the top hat on the front lens-holder of the fixture:

.Loosen 4 lens holder quarter-turn screws and hook both securing springs to the plastic projections in the front 

lens-holder.Tighten the 4 lens holder quarter-turn screws again.

.Put desired top hat onto a front lens-holder and fasten it by two fastening screws.

3.Snap both springs to the slots in the top hat.

Safety 

cable

Quarter-turn screws

Quarter-turn 

screws

Nut

Bolt

Slot

Securing spring

Plastic projection

Securing spring

Top hat

Fastening screw

Fastening screw

Lens-holder

Содержание Color Wash 700E AT






































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды