8
Lamp Adjustment
--- This function can be used when you make the fine adjustment of the lamp.If you select
this function,all effects will be canceled,shutter will be opened and the dimmer intensity will be set onto 100%.By
using the options “
PAn, Tilt, Zoom
” you can aim the light at a flat surface (wall) and perform the fine lamp
adjustment.
Effect Adjustment
--- By this function you can calibrate and adjust the effects to their standard/right positi-
ons.Disconect the DMX controller from the fixture and select “
DMX Values
” menu.The display shows step by
step effects by which you can adjust the fixture to the required position before the function calibration. When
the positioning is finished ,select
“Calibrate Values”
and press [ENTER]:
. Calibration via the control board
Select desired effect, press [ENTER] and adjust its right value (0 - 255). This can be repeated for each calibred
effect if it is required. When the calibration is finished, it is necessary to use the
“Save and Reset”
function to
write the calibration values to the memory and to make a reset in order to check the newly adjusted positions
of the calibrated effects.
List of the calibrated effects:
Colour Wheel
Yellow
Effect indexing
Mech. dimmer 2
Cyan
CTF filter
Zoom
Magenta
Effect wheel
Mech. dimmer
. Calibration via the DMX controller
Connect the DMX controller to the fixture.Now you can calibrate the selected effect by your controller.
Effect
Mode 1 Mode 2 Mode 3
Mode 4 Mode 5 Mode 6
Colour wheel channel 3
channel 9
channel 5
channel
channel 4
channel
Cyan
channel 24
channel 20
channel 26
channel 22
channel 5
channel 3
Magenta
channel 5
Channel
channel 7
channel 3
channel 6
channel 4
Yellow
channel 6
channel
channel 8
channel 4
channel 7
channel 5
Amber
channel 27
channel 23
channel 29
channel 25
channel 28
channel 26
Effect wheel
channel 28
channel 24
channel 30
channel 26
channel 29
channel 27
Effect indexing channel 29
channel 25
channel 31
channel 27
channel 30
channel 28
Zoom
channel 30
channel 26
channel 32
channel 28
channel 31
channel 29
Mech. dimmer 1channel 31
channel 27
channel 33
channel 29
channel 32
channel 30
Mech. dimmer 2channel 32
channel 28
channel 34
channel 30
channel 33
channel 31
After having calibrated required effects ,use the
“Save and Reset”
function to write the calibration values to
the memory and to make a reset in order to check the newly adjusted positions of the calibrated effects.
Item
„Load Default Values”
restores factory calibration values.
Updating software.
--- Using this function you can update software in the fixture via PC and serial link.
The following are required in order to update software:
- PC running Windows 95/98/2000/XP or Linux
- DMX Software Uploader
- Flash cable RS 232Robe (No.13050624)
Note1
:Software update should execute a qualified person.If you lack qualification, do not attempt the update
yourself and ask for help your ROBE distributor.
Note 2
:DMX address, IP address ,programs -3 and all functions in menu Personality will be set to their default
values.
To update software in the fixture:
1
.Installation of DMX Software Uploader.
1.
DMX Software Uploader program is available from the ROBE web site at WWW.robe.cz.
2
.Make a new directory ( e.g. Robe_Uploader) on your hard disk and download the software to it.
3
.Unpack the program from the archive.Program file has name:DSU_name of corresponding
fixture_SoftwareID.If the Robe fixture is produced in magnetic and electronic ballast version, the
name of DMX Software Uploader is the same for both versions.
SoftwareID describes the versions of fixture software included in DMX Software Uploader. Higher
number means later software versions.
2.
Fixture software updating.
1
.Determine which of your COM port is available on your PC and connect it with to the DMX input
of the fixture using the Flash cable. Do not extend this cable. Disconnect the fixture from the other
fixtures
in DMX chain! Turn on the computer and the fixture. Make sure that the lamp is switched off.
2
.Switch the fixture to the update mode by selecting the option Updating Software in menu Special
Functions on the fixture control panel.(From this option you cannot return back to the main menu.
Содержание Color Wash 700E AT
Страница 1: ... Version 2 1 ...
Страница 37: ...37 ...
