RME Audio Hammerfall Multiface Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 81

background image

20

User's Guide HDSP System Multiface

© RME

12. Operation and Usage

12.1 Playback

The HDSP system can play back audio data only in supported modes (channels, PCM) and
formats (sample rate, bit resolution). Otherwise an error message appears (for example at 22
kHz and 8 bit).

In the audio application being used, HDSP must be selected as output device. This can often
be found in the

Options, Preferences

or

Settings

menus under

Playback Device, Audio Devices,

Audio

etc.

We strongly recommend switching off all system sounds (via >

Control Panel /Sounds

<). Also

HDSP should not be the

Preferred Device

for playback, as this could cause loss of synchroniza-

tion and unwanted noises. If you feel you cannot do without system sounds, you should con-
sider buying a cheap Blaster clone and select this as

Preferred Device

in >

Control Panel

/Multimedia /Audio

<.

The screenshot shows a
typical configuration dia-
log of a (stereo) wave
editor. After selecting a
device, audio data is sent
to an analog or digital
(ADAT / SPDIF) port,
depending on which has
been selected as playback
device.

Increasing the number
and/or size of audio buff-
ers may prevent the audio
signal from breaking up,
but also increases latency
i.e. output is delayed. For
synchronized playback of
audio and MIDI (or simi-
lar), be sure to activate
the checkbox ‘Get position from audio driver’.

The HDSP system’s ADAT optical interface allows sample rates of up to 96 kHz using a stan-
dard ADAT recorder. Single-channel data at this frequency requires two ADAT channels,
achieved using the

Sample Multiplexing

technique. This reduces the number of available ADAT

channels from 8 to 4. Under Windows MME, channels are routed to ADAT devices in double-
speed mode as follows:

•

Only stereo pairs (1+2) and (3+4) of the ADAT port are available

This kind of implementation allows a problem-free usage of the ADAT port in both Single and
Double Speed, as the routing doesn't change. However, the hardware spreads the data differ-
ently: Channel 1 is transmitted via channels 1 and 2, channel 2 via 3 and 4 etc.

Please refer to the diagram in chapter 18.2. Routing for record and playback is identical.

«
...
18
19
20
21
22
...
»

Содержание Hammerfall Multiface


















































































Отзывы:

Нет отзывов

Похожие инструкции для Hammerfall Multiface

Бренд: ABB Страницы: 11

Бренд: GALBIATI Страницы: 20

Бренд: LAWO Страницы: 459

Бренд: earline Страницы: 13

Бренд: vanEE Страницы: 52

Бренд: Caddon Hives Страницы: 3

Бренд: Olsen Страницы: 4

Бренд: Fakir Страницы: 22

Бренд: PASCO Страницы: 30

Chicken Coop Plan 3x5

Бренд: EASY COOPS Страницы: 21

Chicken Coop Plan 4x6

Бренд: EASY COOPS Страницы: 18

Chicken Coop Plan 8x10

Бренд: EASY COOPS Страницы: 18

Бренд: Yamaha Страницы: 126

DM 2000 Version 2

Бренд: Yamaha Страницы: 8

Бренд: Vaillant Страницы: 76

Бренд: H2flow Страницы: 2

Бренд: V-TAC Страницы: 27

Бренд: Yacht Sentinel Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды