RME Audio Hammerfall Multiface Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 81

background image

10

User's Guide HDSP System Multiface

© RME

The mobile operation of the HDSP system can cause problems. Explanations and solutions on
digital noise, ground loops, headphone operation and Line Out wiring, power supplies and the
mobile operation with battery can be found in the Tech Info:

HDSP System: Notebook Basics - The Audio Notebook in Practise

.

7. Accessories

RME offers several optional accessories. Additionally parts of the HDSP system are available
separately.

Part Number Description

36000   19“, 1UH Universal rack holder

This 19" rack holder has holes for Digiface and Multiface. Two units can be installed side by
side in any combination. The rack holder also includes holes for nearly all 19" half-rack units
from other manufacturers.

36001   Firewire cable IEEE1394 6M/6M, 1 m (3.3 ft)
36002   Firewire cable IEEE1394 6M/6M, 3 m (9.9 ft)
36005   Firewire cable IEEE1394 6M/6M, 5 m (16.4 ft)
36010   Firewire cable IEEE1394 6M/6M, 10 m (32.8 ft)

Firewire cable for the HDSP system, both sides 6-pin male. Cable longer than 16 ft is not al-
lowed for FireWire, therefore hard to get in computer shops. However the HDSP system does
not use FireWire protocol, therefore can operate flawlessly even with a cable length of up to
50ft (15 m).

36003   Optical cable, TOSLINK, 0.5 m (1.6 ft)
36004   Optical cable, TOSLINK, 1 m (3.3 ft)
36006   Optical cable, TOSLINK, 2 m (6.6 ft)
36007   Optical cable, TOSLINK, 3 m (9.9 ft)
36008   Optical cable, TOSLINK, 5 m (16.4 ft)
36009   Optical cable, TOSLINK, 10 m (33 ft)

Standard lightpipe with TOSLINK connectors, RME approved quality.

37011   Power supply for HDSP CardBus card

Robust and light weigth switching power supply, 100V-240V AC, 12V 1.25 A DC.

«
...
8
9
10
11
12
...
»

Содержание Hammerfall Multiface


















































































Отзывы:

Нет отзывов

Похожие инструкции для Hammerfall Multiface

Бренд: Tascam Страницы: 27

Бренд: Jay-Lor Страницы: 72

Бренд: MacDon Страницы: 198

Бренд: M-Triangel Страницы: 6

Бренд: Faderfox Страницы: 8

Бренд: Sagola Страницы: 62

Бренд: Baileigh Industrial Страницы: 12

ZA top SM315.100A

Бренд: ZIEHL-ABEGG Страницы: 76

Бренд: Parker Страницы: 24

Бренд: Kattsafe Страницы: 19

Бренд: ebm-papst Страницы: 10

CEAG Exit Cube 33822 LED CGLine+

Бренд: Eaton Страницы: 20

Бренд: swamp Страницы: 5

Бренд: Meyer Страницы: 100

Rovelight RT-400

Бренд: Orlit Страницы: 16

Бренд: U.S.SAWS Страницы: 21

ClusterStor H-6167

Бренд: Cray Страницы: 39

Elitco Lighting C202

Бренд: ELEGANT Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды