RLS Wacon SYCON P-value Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 84

RLS Wacon SYCON P-value Скачать руководство пользователя страница 52

July 2022

© RLS Wacon analytics GmbH +49 (0)5121 281260

[email protected]

Pag

e

52

Subject to

change without notice

Configuration

Limit value 1

You will see an input keyboard on the right.
Now use the arrow keys [

◀

], [

▶

], [

▲

] and [

▼

] to move the

black cursor to the desired digit and press the [OK] key.
The selected digit appears in a frame on the left.
Repeat the entry until the desired limit value appears in the
frame. Now move the cursor to the OK field on the keyboard
and press the [OK] key.

You will see the following information on the left:
Current:

currently programmed value

Minimum:

smallest adjustable value

Maximum:

largest adjustable value

If the value at "Current" corresponds to your wish, you do not
need to enter the number again and can immediately move
the cursor to the OK field in
on the keyboard and confirm with the [OK] key.

Limit value 2

Enter the lower limit value 2, which relay 2 is to be switched
when it is exceeded/fallen short of.

Press the [OK] key.

Limit value 2

You will see an input keyboard on the right.
Now use the arrow keys [

◀

], [

▶

], [

▲

] and [

▼

] to move the

black cursor to the desired digit and press the [OK] key. The
selected digit appears in a frame on the left. Repeat the entry
until the desired limit value appears in the frame. Now move
the cursor to the OK field on the keyboard and press the [OK]
key.

You will see the following information on the left:
Current:

currently programmed value

Minimum:

smallest adjustable value

Maximum:

largest adjustable value

If the value at "Current" corresponds to your wish, you do not
need to enter the number again and can immediately move
the cursor to the OK field in the keyboard and confirm with
the [OK] key.

Kommentiert [JA3]:

Mmol/l bild

Kommentiert [JA4]:

Mmol/l bild

«
...
50
51
52
53
54
...
»

Содержание SYCON P-value





















































































Отзывы:

Нет отзывов