background image

IMS01P12-E1 

 

7

6.3 CC-Link Connection 

 

Method to connect 

The PLC (master station) and V-TIO-L/V-TIO-M module make 
multi-drop connection in CC-Link dedicated cable Ver. 1.10. 

 

 

CC-Link dedicated cable 
Ver.1.10 

Up to 61 stations 

PLC 

Master station 

Terminating

resistor 

Station to station cable length: 20 cm or more 

Terminating 

resistor 

 

 

 

Terminal numbers and signal details 

The CC-Link connecting terminal cannot do on-line 
installation or dismount for terminal block of 
dismount impossibility. This instrument exchanges 
all the links after being downed. In addition, FG 
(flame gland) terminal of terminal number 5 is FG in 
a CC-Link function, and it is not FG of instrument all.

 

 

Ground both ends of the shield wire on the twisted 
pair cable via the SLD or FG terminal of each 
module. In addition, the SLD terminal is internally 
connected with the FG terminal. 

 

Do not ground the instrument together with other 
equipment. In addition, use grounding wires with 
across section of 2.0 mm

or more. 

(Ground resistance: 100 ohm or less)

 

 

CC-Link connection terminals 

1: DA 

2: DB 

3: DG 

4: SLD 

5: FG 

Terminal screws 

Screw size: M3 
Recommended tightening torque: 
 0.4 

N

m (4 kgf

cm) 

 

 

Terminal No. 

Signal name 

Symbol 

Cable color

1 Data 

DA 

Blue 

2 Data 

DB 

White 

3 Data 

ground 

DG 

Yellow 

4 Shield 

SLD 

Grounding wire

(Shield) 

5 Frame 

ground

FG 

 

 

For cable specifications, connection method and vendor, 
refer to the home page of CC-Link Partner Association. 

URL: http://www.cc-link.org/ 

 

 

Connection diagram 

 

CC-Link dedicated 
cable Ver.1.10 

CC-Link dedicated 
cable Ver.1.10 

DA 

DB 

DG 

SLD 

FG 

DA 

DB 

DG 

SLD 

FG 

DA

DB

DG

SLD

FG

V-TIO-L/V-TIO-M 

module 

Master station 

V-TIO-L/V-TIO-M 

module 

TR: Terminating resistor

(110 

 

 5 % 1/2 W)

TR 

TR

 

 

Always connect a terminating resistor between the DA and 
DB terminals of the module to be located at the far end. 

6.4 Event Input/Output Connector 

 

Connector pin configuration 

This is a connector installed in the V-TIO-L/V-TIO-M module only 
when provided with the event input (optional) or the event output 
(optional). 

 

 

Event connector   

(socket) 

 

 

 

Circuit configuration 

 

 

24 V DC 

1

2

3

DI

4

5

6

Load

DO1 

DO2 

Load

 

 

 

Attention in connector (plug) wiring 

  Use the following connector (plug) as that connected to the 

event connector.   
Connector (plug) is sold separately. 

SRVP-01 (Front-screw type) 
SRVP-02 (Side-screw type) 

  The lead wires use the stranded wire. 

  Use the stranded wire from size 0.2 to 2.5 mm

2

 (AWG 24-12). 

  Stripping length is as follows.

 

SRVP-01: 10 mm 
SRVP-02: 7 mm 

  Recommended tightening torque of the lead wire in the 

connector (plug):  0.5 to 0.6 N

m (5 to 6 kgf

cm) 

Screw size:  SRVP-01:  M2.5 
 SRVP-02: 

M3 

 

[SRVP-01] Front-screw type 

[SRVP-02] Side-screw type

Stripping length

10 mm 

Stranded wire size: 
 0.2 

to 

2.5 

mm

 (AW G 

24-12) 

Recommended tightening 
torque:  0.5 to 0.6 N

 

(5 to 6 kgf

cm) 

Stripping length

7 mm 

Stranded wire size: 
 

0.2 to 2.5 mm

 (AW G 

24-12) 

Recommended tightening 
torque:  0.5 to 0.6 N

 

(5 to 6 kgf

cm) 

 

 
 

 

 

Pin 
No. 

Description 

Digital input (DI)  (

Digital input (DI)  (

Digital output (DO) 1 
(Relay contact output)

Digital output (DO) 2 
(Relay contact output)

 

 

 

Содержание V-TIO-L









Отзывы: