Riverstone Networks MONT-12 Скачать руководство пользователя

Страница: 34 / 50

WWW.RSIWW.COM

32 of 48

NOTE: VIEWS FROM OUTSIDE.

WARNING: Use two people to install roof ridge. Place ladder in inside of greenhouse.

One person will stand on the ladder holding the ridge with screws FACING UP until

it is in the proper position. Turn over so bolts face down and secured in place.

Use two people and a step ladder. Place step ladder inside greenhouse. Hold

the roof ridge with the screws FACING UP until it is in position. Have one

person inside greenhouse supporting ridge as you slide it into position.

Avoid touching top of front and back of greenhouse until each end is

flush with ends of front and back profiles. Turn the roof ridge over

so bolts face down and rest on top of front and back walls.

7.3A

Working from outside, ensure all pieces are still flush and secure roof ridge to front. Loosen set

screws and adjust position to fit holes in C-2 connector. Secure with three bolts.

7.5A

Working from inside, secure roof ridge to front end wall. Loosen T-bolts and adjust position

to fit holes in B-7 connector. Secure with two bolts.

7.4A

Repeat step 7.5A to secure back.

7.5B

Repeat step 7.4A to secure back.

7.4B

Make sure end of roof ridge is

flush to profiles on front and back.

7.3B

NOTE: VIEWS FROM INSIDE.

R-1E

R-1

F-7

B-7

S-2C

Connector

QTY

B-7

C-2

In some cases the corner points

might need to be trimmed down if

roof ridge is sitting on points.

See orange.

Connector

QTY

S-7

C-2

S-2C

2
6

Содержание MONT-12



















































Результаты поиска

Содержание MONT-12

Отзывы:

Похожие инструкции для MONT-12

Бренды по названию

Популярные бренды

Riverstone Networks MONT-12, Руководство по сборке

Результаты поиска

Содержание MONT-12

Отзывы:

Похожие инструкции для MONT-12

Бренды по названию

Популярные бренды