Nr.
x
H
8
I
6
J
8
Nr.
x
D
1
E
2
F
2
G
2
Sweet Tomato
Nr.
x
A
1
B
1
C1
1
C2
1
1
Assembly Instructions
Helpline Number
If you have any problems or queries with this product please call our helpline on
+44 (0)1406 372227 between the hours of 9am to 5.30pm Monday to Friday.
Gardman Limited, High Street, Moulton, Spalding, Lincolnshire PE12 6QD
08895
Wooden cold frame
Before You Start
Please check that all components are present and read through
these instructions carefully.
Assembly
1. Check all screws are tight in the ready-made frame sections
but avoid over-tightening.
2. Do not yet remove the protective covers on the
polycarbonate glazing: note the cover is on the outside of
the panels.
3. Assemble the frame body (parts
A, B, & C1 & C2
) using the
large screws (
H
) and the pre-drilled holes in the frame.
(See Fig 1).
4. Fix the base plates (
G
) on the underside of two corners as
required, using screws (
J
).
5. Place the lid (
D
) in position so that the hinges are at the
back and are facing downwards. Line up the lid with the
frame sides and hold firmly whilst attaching the hinges to
the back panel (
A
) using screws (
I
). (See Fig 3).
6. To assemble the lid support arms:
a. Pass the washers over bolts (
F
) and insert the bolts, from
the outside, through the slots in the support arms and
into the pre-drilled holes in the sides (
C1 & C2
). Screw in
part way to secure it. (See Fig 4).
b. Tighten the wing bolt when the lid is in the required
position.
7. To complete the assembly, peel off the protective sheet
from the polycarbonate panels and site the cold frame in
good light but out of prolonged fierce sunlight. Use the
corner base plates to peg or bolt down the cold frame if
extra security is required.
Care & maintenance
•
Extra coatings of wood preservative will prolong the life
of the product but be sure to use one that is harmless to
plants.
•
Avoid constant contact with wet soil by mounting the
frame on bricks, slabs or wooden battens.
Parts & Fittings Supplied
Assembly Instructions
Helpline Number
If you have any problems or queries with this product please call our helpline on
+44 (0)1406 372227 between the hours of 9am to 5.30pm Monday to Friday.
Gardman Limited, High Street, Moulton, Spalding, Lincolnshire PE12 6QD
08895
Wooden cold frame
Before You Start
Please check that all components are present and read through
these instructions carefully.
Assembly
1. Check all screws are tight in the ready-made frame sections
but avoid over-tightening.
2. Do not yet remove the protective covers on the
polycarbonate glazing: note the cover is on the outside of
the panels.
3. Assemble the frame body (parts
A, B, & C1 & C2
) using the
large screws (
H
) and the pre-drilled holes in the frame.
(See Fig 1).
4. Fix the base plates (
G
) on the underside of two corners as
required, using screws (
J
).
5. Place the lid (
D
) in position so that the hinges are at the
back and are facing downwards. Line up the lid with the
frame sides and hold firmly whilst attaching the hinges to
the back panel (
A
) using screws (
I
). (See Fig 3).
6. To assemble the lid support arms:
a. Pass the washers over bolts (
F
) and insert the bolts, from
the outside, through the slots in the support arms and
into the pre-drilled holes in the sides (
C1 & C2
). Screw in
part way to secure it. (See Fig 4).
b. Tighten the wing bolt when the lid is in the required
position.
7. To complete the assembly, peel off the protective sheet
from the polycarbonate panels and site the cold frame in
good light but out of prolonged fierce sunlight. Use the
corner base plates to peg or bolt down the cold frame if
extra security is required.
Care & maintenance
•
Extra coatings of wood preservative will prolong the life
of the product but be sure to use one that is harmless to
plants.
•
Avoid constant contact with wet soil by mounting the
frame on bricks, slabs or wooden battens.
Parts & Fittings Supplied
Assembly Instructions
Helpline Number
If you have any problems or queries with this product please call our helpline on
+44 (0)1406 372227 between the hours of 9am to 5.30pm Monday to Friday.
Gardman Limited, High Street, Moulton, Spalding, Lincolnshire PE12 6QD
08895
Wooden cold frame
Before You Start
Please check that all components are present and read through
these instructions carefully.
Assembly
1. Check all screws are tight in the ready-made frame sections
but avoid over-tightening.
2. Do not yet remove the protective covers on the
polycarbonate glazing: note the cover is on the outside of
the panels.
3. Assemble the frame body (parts
A, B, & C1 & C2
) using the
large screws (
H
) and the pre-drilled holes in the frame.
(See Fig 1).
4. Fix the base plates (
G
) on the underside of two corners as
required, using screws (
J
).
5. Place the lid (
D
) in position so that the hinges are at the
back and are facing downwards. Line up the lid with the
frame sides and hold firmly whilst attaching the hinges to
the back panel (
A
) using screws (
I
). (See Fig 3).
6. To assemble the lid support arms:
a. Pass the washers over bolts (
F
) and insert the bolts, from
the outside, through the slots in the support arms and
into the pre-drilled holes in the sides (
C1 & C2
). Screw in
part way to secure it. (See Fig 4).
b. Tighten the wing bolt when the lid is in the required
position.
7. To complete the assembly, peel off the protective sheet
from the polycarbonate panels and site the cold frame in
good light but out of prolonged fierce sunlight. Use the
corner base plates to peg or bolt down the cold frame if
extra security is required.
Care & maintenance
•
Extra coatings of wood preservative will prolong the life
of the product but be sure to use one that is harmless to
plants.
•
Avoid constant contact with wet soil by mounting the
frame on bricks, slabs or wooden battens.
Parts & Fittings Supplied
Assembly Instructions
Helpline Number
If you have any problems or queries with this product please call our helpline on
+44 (0)1406 372227 between the hours of 9am to 5.30pm Monday to Friday.
Gardman Limited, High Street, Moulton, Spalding, Lincolnshire PE12 6QD
08895
Wooden cold frame
Before You Start
Please check that all components are present and read through
these instructions carefully.
Assembly
1. Check all screws are tight in the ready-made frame sections
but avoid over-tightening.
2. Do not yet remove the protective covers on the
polycarbonate glazing: note the cover is on the outside of
the panels.
3. Assemble the frame body (parts
A, B, & C1 & C2
) using the
large screws (
H
) and the pre-drilled holes in the frame.
(See Fig 1).
4. Fix the base plates (
G
) on the underside of two corners as
required, using screws (
J
).
5. Place the lid (
D
) in position so that the hinges are at the
back and are facing downwards. Line up the lid with the
frame sides and hold firmly whilst attaching the hinges to
the back panel (
A
) using screws (
I
). (See Fig 3).
6. To assemble the lid support arms:
a. Pass the washers over bolts (
F
) and insert the bolts, from
the outside, through the slots in the support arms and
into the pre-drilled holes in the sides (
C1 & C2
). Screw in
part way to secure it. (See Fig 4).
b. Tighten the wing bolt when the lid is in the required
position.
7. To complete the assembly, peel off the protective sheet
from the polycarbonate panels and site the cold frame in
good light but out of prolonged fierce sunlight. Use the
corner base plates to peg or bolt down the cold frame if
extra security is required.
Care & maintenance
•
Extra coatings of wood preservative will prolong the life
of the product but be sure to use one that is harmless to
plants.
•
Avoid constant contact with wet soil by mounting the
frame on bricks, slabs or wooden battens.
Parts & Fittings Supplied
Assembly Instructions
Helpline Number
If you have any problems or queries with this product please call our helpline on
+44 (0)1406 372227 between the hours of 9am to 5.30pm Monday to Friday.
Gardman Limited, High Street, Moulton, Spalding, Lincolnshire PE12 6QD
08895
Wooden cold frame
Before You Start
Please check that all components are present and read through
these instructions carefully.
Assembly
1. Check all screws are tight in the ready-made frame sections
but avoid over-tightening.
2. Do not yet remove the protective covers on the
polycarbonate glazing: note the cover is on the outside of
the panels.
3. Assemble the frame body (parts
A, B, & C1 & C2
) using the
large screws (
H
) and the pre-drilled holes in the frame.
(See Fig 1).
4. Fix the base plates (
G
) on the underside of two corners as
required, using screws (
J
).
5. Place the lid (
D
) in position so that the hinges are at the
back and are facing downwards. Line up the lid with the
frame sides and hold firmly whilst attaching the hinges to
the back panel (
A
) using screws (
I
). (See Fig 3).
6. To assemble the lid support arms:
a. Pass the washers over bolts (
F
) and insert the bolts, from
the outside, through the slots in the support arms and
into the pre-drilled holes in the sides (
C1 & C2
). Screw in
part way to secure it. (See Fig 4).
b. Tighten the wing bolt when the lid is in the required
position.
7. To complete the assembly, peel off the protective sheet
from the polycarbonate panels and site the cold frame in
good light but out of prolonged fierce sunlight. Use the
corner base plates to peg or bolt down the cold frame if
extra security is required.
Care & maintenance
•
Extra coatings of wood preservative will prolong the life
of the product but be sure to use one that is harmless to
plants.
•
Avoid constant contact with wet soil by mounting the
frame on bricks, slabs or wooden battens.
Parts & Fittings Supplied
Assembly Instructions
Helpline Number
If you have any problems or queries with this product please call our helpline on
+44 (0)1406 372227 between the hours of 9am to 5.30pm Monday to Friday.
Gardman Limited, High Street, Moulton, Spalding, Lincolnshire PE12 6QD
08895
Wooden cold frame
Before You Start
Please check that all components are present and read through
these instructions carefully.
Assembly
1. Check all screws are tight in the ready-made frame sections
but avoid over-tightening.
2. Do not yet remove the protective covers on the
polycarbonate glazing: note the cover is on the outside of
the panels.
3. Assemble the frame body (parts
A, B, & C1 & C2
) using the
large screws (
H
) and the pre-drilled holes in the frame.
(See Fig 1).
4. Fix the base plates (
G
) on the underside of two corners as
required, using screws (
J
).
5. Place the lid (
D
) in position so that the hinges are at the
back and are facing downwards. Line up the lid with the
frame sides and hold firmly whilst attaching the hinges to
the back panel (
A
) using screws (
I
). (See Fig 3).
6. To assemble the lid support arms:
a. Pass the washers over bolts (
F
) and insert the bolts, from
the outside, through the slots in the support arms and
into the pre-drilled holes in the sides (
C1 & C2
). Screw in
part way to secure it. (See Fig 4).
b. Tighten the wing bolt when the lid is in the required
position.
7. To complete the assembly, peel off the protective sheet
from the polycarbonate panels and site the cold frame in
good light but out of prolonged fierce sunlight. Use the
corner base plates to peg or bolt down the cold frame if
extra security is required.
Care & maintenance
•
Extra coatings of wood preservative will prolong the life
of the product but be sure to use one that is harmless to
plants.
•
Avoid constant contact with wet soil by mounting the
frame on bricks, slabs or wooden battens.
Parts & Fittings Supplied
Assembly Instructions
Helpline Number
If you have any problems or queries with this product please call our helpline on
+44 (0)1406 372227 between the hours of 9am to 5.30pm Monday to Friday.
Gardman Limited, High Street, Moulton, Spalding, Lincolnshire PE12 6QD
08895
Wooden cold frame
Before You Start
Please check that all components are present and read through
these instructions carefully.
Assembly
1. Check all screws are tight in the ready-made frame sections
but avoid over-tightening.
2. Do not yet remove the protective covers on the
polycarbonate glazing: note the cover is on the outside of
the panels.
3. Assemble the frame body (parts
A, B, & C1 & C2
) using the
large screws (
H
) and the pre-drilled holes in the frame.
(See Fig 1).
4. Fix the base plates (
G
) on the underside of two corners as
required, using screws (
J
).
5. Place the lid (
D
) in position so that the hinges are at the
back and are facing downwards. Line up the lid with the
frame sides and hold firmly whilst attaching the hinges to
the back panel (
A
) using screws (
I
). (See Fig 3).
6. To assemble the lid support arms:
a. Pass the washers over bolts (
F
) and insert the bolts, from
the outside, through the slots in the support arms and
into the pre-drilled holes in the sides (
C1 & C2
). Screw in
part way to secure it. (See Fig 4).
b. Tighten the wing bolt when the lid is in the required
position.
7. To complete the assembly, peel off the protective sheet
from the polycarbonate panels and site the cold frame in
good light but out of prolonged fierce sunlight. Use the
corner base plates to peg or bolt down the cold frame if
extra security is required.
Care & maintenance
•
Extra coatings of wood preservative will prolong the life
of the product but be sure to use one that is harmless to
plants.
•
Avoid constant contact with wet soil by mounting the
frame on bricks, slabs or wooden battens.
Parts & Fittings Supplied
Assembly Instructions
Helpline Number
If you have any problems or queries with this product please call our helpline on
+44 (0)1406 372227 between the hours of 9am to 5.30pm Monday to Friday.
Gardman Limited, High Street, Moulton, Spalding, Lincolnshire PE12 6QD
08895
Wooden cold frame
Before You Start
Please check that all components are present and read through
these instructions carefully.
Assembly
1. Check all screws are tight in the ready-made frame sections
but avoid over-tightening.
2. Do not yet remove the protective covers on the
polycarbonate glazing: note the cover is on the outside of
the panels.
3. Assemble the frame body (parts
A, B, & C1 & C2
) using the
large screws (
H
) and the pre-drilled holes in the frame.
(See Fig 1).
4. Fix the base plates (
G
) on the underside of two corners as
required, using screws (
J
).
5. Place the lid (
D
) in position so that the hinges are at the
back and are facing downwards. Line up the lid with the
frame sides and hold firmly whilst attaching the hinges to
the back panel (
A
) using screws (
I
). (See Fig 3).
6. To assemble the lid support arms:
a. Pass the washers over bolts (
F
) and insert the bolts, from
the outside, through the slots in the support arms and
into the pre-drilled holes in the sides (
C1 & C2
). Screw in
part way to secure it. (See Fig 4).
b. Tighten the wing bolt when the lid is in the required
position.
7. To complete the assembly, peel off the protective sheet
from the polycarbonate panels and site the cold frame in
good light but out of prolonged fierce sunlight. Use the
corner base plates to peg or bolt down the cold frame if
extra security is required.
Care & maintenance
•
Extra coatings of wood preservative will prolong the life
of the product but be sure to use one that is harmless to
plants.
•
Avoid constant contact with wet soil by mounting the
frame on bricks, slabs or wooden battens.
Parts & Fittings Supplied
Assembly Instructions
Helpline Number
If you have any problems or queries with this product please call our helpline on
+44 (0)1406 372227 between the hours of 9am to 5.30pm Monday to Friday.
Gardman Limited, High Street, Moulton, Spalding, Lincolnshire PE12 6QD
08895
Wooden cold frame
Before You Start
Please check that all components are present and read through
these instructions carefully.
Assembly
1. Check all screws are tight in the ready-made frame sections
but avoid over-tightening.
2. Do not yet remove the protective covers on the
polycarbonate glazing: note the cover is on the outside of
the panels.
3. Assemble the frame body (parts
A, B, & C1 & C2
) using the
large screws (
H
) and the pre-drilled holes in the frame.
(See Fig 1).
4. Fix the base plates (
G
) on the underside of two corners as
required, using screws (
J
).
5. Place the lid (
D
) in position so that the hinges are at the
back and are facing downwards. Line up the lid with the
frame sides and hold firmly whilst attaching the hinges to
the back panel (
A
) using screws (
I
). (See Fig 3).
6. To assemble the lid support arms:
a. Pass the washers over bolts (
F
) and insert the bolts, from
the outside, through the slots in the support arms and
into the pre-drilled holes in the sides (
C1 & C2
). Screw in
part way to secure it. (See Fig 4).
b. Tighten the wing bolt when the lid is in the required
position.
7. To complete the assembly, peel off the protective sheet
from the polycarbonate panels and site the cold frame in
good light but out of prolonged fierce sunlight. Use the
corner base plates to peg or bolt down the cold frame if
extra security is required.
Care & maintenance
•
Extra coatings of wood preservative will prolong the life
of the product but be sure to use one that is harmless to
plants.
•
Avoid constant contact with wet soil by mounting the
frame on bricks, slabs or wooden battens.
Parts & Fittings Supplied
Assembly Instructions
Helpline Number
If you have any problems or queries with this product please call our helpline on
+44 (0)1406 372227 between the hours of 9am to 5.30pm Monday to Friday.
Gardman Limited, High Street, Moulton, Spalding, Lincolnshire PE12 6QD
08895
Wooden cold frame
Before You Start
Please check that all components are present and read through
these instructions carefully.
Assembly
1. Check all screws are tight in the ready-made frame sections
but avoid over-tightening.
2. Do not yet remove the protective covers on the
polycarbonate glazing: note the cover is on the outside of
the panels.
3. Assemble the frame body (parts
A, B, & C1 & C2
) using the
large screws (
H
) and the pre-drilled holes in the frame.
(See Fig 1).
4. Fix the base plates (
G
) on the underside of two corners as
required, using screws (
J
).
5. Place the lid (
D
) in position so that the hinges are at the
back and are facing downwards. Line up the lid with the
frame sides and hold firmly whilst attaching the hinges to
the back panel (
A
) using screws (
I
). (See Fig 3).
6. To assemble the lid support arms:
a. Pass the washers over bolts (
F
) and insert the bolts, from
the outside, through the slots in the support arms and
into the pre-drilled holes in the sides (
C1 & C2
). Screw in
part way to secure it. (See Fig 4).
b. Tighten the wing bolt when the lid is in the required
position.
7. To complete the assembly, peel off the protective sheet
from the polycarbonate panels and site the cold frame in
good light but out of prolonged fierce sunlight. Use the
corner base plates to peg or bolt down the cold frame if
extra security is required.
Care & maintenance
•
Extra coatings of wood preservative will prolong the life
of the product but be sure to use one that is harmless to
plants.
•
Avoid constant contact with wet soil by mounting the
frame on bricks, slabs or wooden battens.
Parts & Fittings Supplied
Assembly Instructions
Helpline Number
If you have any problems or queries with this product please call our helpline on
+44 (0)1406 372227 between the hours of 9am to 5.30pm Monday to Friday.
Gardman Limited, High Street, Moulton, Spalding, Lincolnshire PE12 6QD
08895
Wooden cold frame
Before You Start
Please check that all components are present and read through
these instructions carefully.
Assembly
1. Check all screws are tight in the ready-made frame sections
but avoid over-tightening.
2. Do not yet remove the protective covers on the
polycarbonate glazing: note the cover is on the outside of
the panels.
3. Assemble the frame body (parts
A, B, & C1 & C2
) using the
large screws (
H
) and the pre-drilled holes in the frame.
(See Fig 1).
4. Fix the base plates (
G
) on the underside of two corners as
required, using screws (
J
).
5. Place the lid (
D
) in position so that the hinges are at the
back and are facing downwards. Line up the lid with the
frame sides and hold firmly whilst attaching the hinges to
the back panel (
A
) using screws (
I
). (See Fig 3).
6. To assemble the lid support arms:
a. Pass the washers over bolts (
F
) and insert the bolts, from
the outside, through the slots in the support arms and
into the pre-drilled holes in the sides (
C1 & C2
). Screw in
part way to secure it. (See Fig 4).
b. Tighten the wing bolt when the lid is in the required
position.
7. To complete the assembly, peel off the protective sheet
from the polycarbonate panels and site the cold frame in
good light but out of prolonged fierce sunlight. Use the
corner base plates to peg or bolt down the cold frame if
extra security is required.
Care & maintenance
•
Extra coatings of wood preservative will prolong the life
of the product but be sure to use one that is harmless to
plants.
•
Avoid constant contact with wet soil by mounting the
frame on bricks, slabs or wooden battens.
Parts & Fittings Supplied
Assembly Instructions
Helpline Number
If you have any problems or queries with this product please call our helpline on
+44 (0)1406 372227 between the hours of 9am to 5.30pm Monday to Friday.
Gardman Limited, High Street, Moulton, Spalding, Lincolnshire PE12 6QD
08895
Wooden cold frame
Before You Start
Please check that all components are present and read through
these instructions carefully.
Assembly
1. Check all screws are tight in the ready-made frame sections
but avoid over-tightening.
2. Do not yet remove the protective covers on the
polycarbonate glazing: note the cover is on the outside of
the panels.
3. Assemble the frame body (parts
A, B, & C1 & C2
) using the
large screws (
H
) and the pre-drilled holes in the frame.
(See Fig 1).
4. Fix the base plates (
G
) on the underside of two corners as
required, using screws (
J
).
5. Place the lid (
D
) in position so that the hinges are at the
back and are facing downwards. Line up the lid with the
frame sides and hold firmly whilst attaching the hinges to
the back panel (
A
) using screws (
I
). (See Fig 3).
6. To assemble the lid support arms:
a. Pass the washers over bolts (
F
) and insert the bolts, from
the outside, through the slots in the support arms and
into the pre-drilled holes in the sides (
C1 & C2
). Screw in
part way to secure it. (See Fig 4).
b. Tighten the wing bolt when the lid is in the required
position.
7. To complete the assembly, peel off the protective sheet
from the polycarbonate panels and site the cold frame in
good light but out of prolonged fierce sunlight. Use the
corner base plates to peg or bolt down the cold frame if
extra security is required.
Care & maintenance
•
Extra coatings of wood preservative will prolong the life
of the product but be sure to use one that is harmless to
plants.
•
Avoid constant contact with wet soil by mounting the
frame on bricks, slabs or wooden battens.
Parts & Fittings Supplied
Assembly Instructions
Helpline Number
If you have any problems or queries with this product please call our helpline on
+44 (0)1406 372227 between the hours of 9am to 5.30pm Monday to Friday.
Gardman Limited, High Street, Moulton, Spalding, Lincolnshire PE12 6QD
08895
Wooden cold frame
Before You Start
Please check that all components are present and read through
these instructions carefully.
Assembly
1. Check all screws are tight in the ready-made frame sections
but avoid over-tightening.
2. Do not yet remove the protective covers on the
polycarbonate glazing: note the cover is on the outside of
the panels.
3. Assemble the frame body (parts
A, B, & C1 & C2
) using the
large screws (
H
) and the pre-drilled holes in the frame.
(See Fig 1).
4. Fix the base plates (
G
) on the underside of two corners as
required, using screws (
J
).
5. Place the lid (
D
) in position so that the hinges are at the
back and are facing downwards. Line up the lid with the
frame sides and hold firmly whilst attaching the hinges to
the back panel (
A
) using screws (
I
). (See Fig 3).
6. To assemble the lid support arms:
a. Pass the washers over bolts (
F
) and insert the bolts, from
the outside, through the slots in the support arms and
into the pre-drilled holes in the sides (
C1 & C2
). Screw in
part way to secure it. (See Fig 4).
b. Tighten the wing bolt when the lid is in the required
position.
7. To complete the assembly, peel off the protective sheet
from the polycarbonate panels and site the cold frame in
good light but out of prolonged fierce sunlight. Use the
corner base plates to peg or bolt down the cold frame if
extra security is required.
Care & maintenance
•
Extra coatings of wood preservative will prolong the life
of the product but be sure to use one that is harmless to
plants.
•
Avoid constant contact with wet soil by mounting the
frame on bricks, slabs or wooden battens.
Parts & Fittings Supplied
G
M4x35
M3x20 (zwart)
M3x25
Assembl
y Instr
uctions
Helpline Number
If y
ou ha
ve an
y pr
oblems or quer
ies with this pr
oduct please call our helpline on
+44 (0)1406 372227 betw
een the hour
s of 9am to 5.30pm Monda
y to F
rida
y.
G
ard
m
an Li
m
ite
d, H
ig
h S
tre
et
, M
ou
lto
n, S
pa
ld
in
g, Li
nc
oln
sh
ire P
E1
2 6
Q
D
08895
W
ooden cold fr
ame
Bef
or
e Y
ou
Star
t
Please c
hec
k that all components ar
e pr
esent and r
ead thr
ough
these instr
uctions car
efull
y.
Assembl
y
1.
Chec
k all scr
ews ar
e tight in the r
ead
y-made fr
ame sections
but a
void o
ver
-tightening
.
2.
Do not y
et r
emo
ve the pr
otectiv
e co
ver
s on the
pol
ycarbonate glazing
: note the co
ver is on the outside of
the panels.
3.
Assemble the fr
ame bod
y (
par
ts
A,
B,
& C1 & C2
) using the
lar
ge scr
ews (
H
) and the pr
e-dr
illed holes in the fr
ame.
(See F
ig 1).
4.
Fix the base plates (
G
) on the under
side of tw
o corner
s as
requir
ed,
using scr
ews (
J
).
5.
Place the lid (
D
) in position so that the hing
es ar
e at the
bac
k and ar
e f
acing do
wnw
ar
ds.
Line up the lid with the
fr
ame sides and hold f
irml
y w
hilst attac
hing the hing
es to
the bac
k panel (
A
) using scr
ews (
I
). (See F
ig 3).
6.
T
o assemble the lid suppor
t arms:
a.
P
ass the w
asher
s o
ver bolts (
F
) and inser
t the bolts,
fr
om
the outside,
thr
ough the slots in the suppor
t arms and
into the pr
e-dr
illed holes in the sides (
C1 & C2
). Scr
ew in
par
t w
ay to secur
e it.
(See F
ig 4).
b.
T
ighten the wing bolt w
hen the lid is in the r
equir
ed
position.
7.
T
o complete the assembl
y, peel of
f the pr
otectiv
e sheet
fr
om the pol
ycarbonate panels and site the cold fr
ame in
good light but out of pr
olong
ed f
ier
ce sunlight.
Use the
corner base plates to peg or bolt do
wn the cold fr
ame if
extr
a secur
ity is r
equir
ed.
Car
e & maint
enance
•
Extr
a coatings of w
ood pr
eserv
ativ
e will pr
olong the lif
e
of the pr
oduct but be sur
e to use one that is harmless to
plants.
•
Av
oid constant contact with w
et soil b
y mounting the
fr
ame on br
ic
ks,
slabs or w
ooden battens.
Par
ts & F
it
tings Supplied
Assembl
y Instr
uctions
Helpline Number
If y
ou ha
ve an
y pr
oblems or quer
ies with this pr
oduct please call our helpline on
+44 (0)1406 372227 betw
een the hour
s of 9am to 5.30pm Monda
y to F
rida
y.
G
ard
m
an Li
m
ite
d, H
ig
h S
tre
et
, M
ou
lto
n, S
pa
ld
in
g, Li
nc
oln
sh
ire P
E1
2 6
Q
D
08895
W
ooden cold fr
ame
Bef
or
e Y
ou
Star
t
Please c
hec
k that all components ar
e pr
esent and r
ead thr
ough
these instr
uctions car
efull
y.
Assembl
y
1.
Chec
k all scr
ews ar
e tight in the r
ead
y-made fr
ame sections
but a
void o
ver
-tightening
.
2.
Do not y
et r
emo
ve the pr
otectiv
e co
ver
s on the
pol
ycarbonate glazing
: note the co
ver is on the outside of
the panels.
3.
Assemble the fr
ame bod
y (
par
ts
A,
B,
& C1 & C2
) using the
lar
ge scr
ews (
H
) and the pr
e-dr
illed holes in the fr
ame.
(See F
ig 1).
4.
Fix the base plates (
G
) on the under
side of tw
o corner
s as
requir
ed,
using scr
ews (
J
).
5.
Place the lid (
D
) in position so that the hing
es ar
e at the
bac
k and ar
e f
acing do
wnw
ar
ds.
Line up the lid with the
fr
ame sides and hold f
irml
y w
hilst attac
hing the hing
es to
the bac
k panel (
A
) using scr
ews (
I
). (See F
ig 3).
6.
T
o assemble the lid suppor
t arms:
a.
P
ass the w
asher
s o
ver bolts (
F
) and inser
t the bolts,
fr
om
the outside,
thr
ough the slots in the suppor
t arms and
into the pr
e-dr
illed holes in the sides (
C1 & C2
). Scr
ew in
par
t w
ay to secur
e it.
(See F
ig 4).
b.
T
ighten the wing bolt w
hen the lid is in the r
equir
ed
position.
7.
T
o complete the assembl
y, peel of
f the pr
otectiv
e sheet
fr
om the pol
ycarbonate panels and site the cold fr
ame in
good light but out of pr
olong
ed f
ier
ce sunlight.
Use the
corner base plates to peg or bolt do
wn the cold fr
ame if
extr
a secur
ity is r
equir
ed.
Car
e & maint
enance
•
Extr
a coatings of w
ood pr
eserv
ativ
e will pr
olong the lif
e
of the pr
oduct but be sur
e to use one that is harmless to
plants.
•
Av
oid constant contact with w
et soil b
y mounting the
fr
ame on br
ic
ks,
slabs or w
ooden battens.
Par
ts & F
it
tings Supplied
J
I
Montagehandleiding / Instructions de montage /
Montageanleitung / Manual
100 L x 65 W x 32/40 H cm RW2171
H
W
L
All manuals and user guides at all-guides.com
all-guides.com
