background image

Operator's Manual

Syct

 2-Man Ladder Stand

Check for parts online at 

www.HuntRiversEdge.com

 or call 800-450-EDGE (3343) M-F 8-5

6

Operator's Manual

Syct

 2-Man Ladder Stand

7.  Attach the seat/frame assembly (17) to the inside of side seat 

support loops (8) using two 1/4-20 x 2-3/4” bolts (25), yellow 

washers (30), nylon spacers (31) and locknuts (27). SEE FIGURE 5.

 

NOTE: The mesh seat is not shown in FIGURE 5 for ease of assembly 

view although it is already factory assembled to the metal seat 

frame. Make sure the metal seat frame is oriented onto the ladder 

assembly correctly with the “channel” portion facing downward, 

towards the foot platform. Mesh seat/backrest should temporarily 

lay on top of seat until its assembly later in assembly instructions.

8.  Attach the backrest rim (13) to the side seat support loops (8) using 

four 1/4-20 x 2-1/4” bolts (23), steel washers (29) and locknuts (27). 

SEE FIGURE 6. You must now tighten all nut and bolt assemblies. 

Be sure not to over tighten or crush tubing when tightening.

9.  With all nut/bolt assemblies tightened, flip the seat/frame assembly 

(17) to the upright position. This must be done in order to allow 

slack in the mesh material to complete seat attachment. Attach 

the mesh backrest and one fabric mount strip (18) to the top side 

of backrest rim (13) using seven 1/4-20 x 1-1/2” bolts (22) and 

locknuts (27). SEE FIGURES 7A AND 7B. The mesh backrest must 

wrap around top side of backrest tube and the plastic stiffening rod 

located in the sewn sleeve of mesh backrest MUST be positioned 

behind the fabric mount strip to act as a stop and prevent the 

backrest from pulling out during use. All bolts MUST go through the 

retainer bar, holes provided in mesh backrest and the backrest rim. 

Tighten these bolts securely at this time. Do not crush tubing 

when tightening. 

10. With the seat still flipped up into the upright position (to allow for 

slack in mesh material), attach the mesh “tail” section of the seat/

frame assembly (17) and one fabric mount strip (18) to the top side 

of tree blade frame (9) using seven 1/4-20 x 1-1/2” bolts (22) and 

locknuts (27). SEE FIGURES 7A AND 7B. The mesh “tail” section 

must be positioned on top side of tree blade tube and the plastic 

stiffening rod located in the sewn sleeve of mesh “tail” section MUST 

be positioned behind the retainer bar to act as a stop and prevent the 

“tail” section from pulling out during use. All bolts MUST go through 

the fabric mount strip, holes provided in mesh “tail” section and the 

tree blade. Tighten these bolts securely at this time. Do not crush 

tubing when tightening. 

FIGURE 6

8

13

27

23

29

FIGURE 7A

22

27

17

18

13

22

18

9

27

18

22

18

22

17

27

FIGURE 7B

17

FIGURE 5

25

8

30

27

31

Содержание Syct RE642

















Отзывы: