background image

Operator's Manual

Syct

 2-Man Ladder Stand

Check for parts online at 

www.HuntRiversEdge.com

 or call 800-450-EDGE (3343) M-F 8-5

10

Operator's Manual

Syct

 2-Man Ladder Stand

SETUP AND USE INSTRUCTIONS

 

During installation and removal of ladder treestands, you must 

always and properly use the included Full Body Harness (Fall Arrest 

System). Refer to the Full Body Harness instructions included with this 

product for proper use.

Figure 4

FIGURE 14

pull tail to take out slack

tightening lever

release lever

feed through slot

FIGURE 15

1.   With assembled product lying on the ground in assembled position, 

position one person at bottom end of ladder. This person has to 

prevent the ladder end from tilting up when platform end is lifted 

and prevent the ladder from skidding across ground.

2.   a. Position two people at the platform end of the ladder, lift the 

platform end and continue uprighting by walking toward bottom 

end of ladder and moving hands along ladder legs. Stand ladder 

up against chosen straight tree on dry, level ground. Use 

caution when ladder comes over center against the tree. 

 

b. Step back and look at the ladder top to see that both platform 

tree blade and upper tree blade are contacting tree. Adjust as 

needed so both the tree blades are contacting tree.

 

c. Step down hard on bottom step to push ladder legs into the 

ground.

3.  a. With stabilizer bar ratchet strap (37) now in hand, wrap the strap 

around the tree and feed the long strap through the center slot of 

ratcheting mechanism and back around through tightening lever. 

SEE FIGURE 14. Secure the ladder tight so the stabilizer bar (4 

and 5) is at a right angle to the tree. Adjust stabilizer bar length as 

necessary so it contacts tree. Be absolutely sure the contact points 

on platform and the contact points on stabilizer bar bark biting 

plate are all contacting tree.

 

NOTE: Be sure you feed the long strap correctly so there are no 

twists in the strap.

 

b. Pull tail of long strap of stabilizer bar ratchet strap (37) until 

most of the slack is taken out. Be sure entire strap is even and at 

the same level all around tree. “Ratchet” tight to tree, ensuring the 

two contact points on stabilizer bar bark biting plate are dug into 

the tree surface securely. This will securely attach the stabilizer bar 

to tree. SEE FIGURES 15 AND 16.

WARNING

Never ascend or descend ladder without criss-cross 

straps/ropes securely holding ladder to tree and stabilizer 

bar securely attached. Failure to correctly perform 

these steps can cause the ladder to collapse/buck-over 

backwards during the initial ascent to attach ratchet strap 

resulting in serious injury or death.

WARNING

Only use approved RETI parts. Failure to do so may result 

in serious injury or death!

FIGURE 16

Ensure teeth are 

dug into the tree

WARNING

Bring ratchet strap(s) up with you in a pocket - Do Not 

carry in your hands!

Содержание Syct RE642

















Отзывы: