background image

Check for parts online at 

www.HuntRiversEdge.com

 or call 800-450-EDGE (3343) M-F 8-5

9

Operator's Manual

Syct

 2-Man Ladder Stand

WARNING

Always wear the appropriate footwear when using a 

ladder treestand. A good non-slip safety boot is important 

to your personal safety. Be especially careful that boot laces 

do not get hooked on the stand or any of its components 

(tuck shoelaces into boots before climbing).
Never stand on seat, it is designed for sitting only.
Do Not allow excessive strap buildup in ratchet as this 

will prevent the ratchet teeth from engaging causing 

slippage.
Always attach ratchet straps securely while using this 

product!
If seat is removable, be certain it is securely attached 

when in use.
Some models include a shooting rail. Never lean against, 

lean over, or sit on shooting rail. It is designed as a 

shooting rest only. Always be aware that the shooting rail 

can swing to one side or pivot up and down.
Some models include a footrest, which is designed as a 

footrest only. Never stand on footrest! Always be fully 

aware of foot placement.
Some models include a multi-piece stabilizer bar system. 

Be sure attachment hardware goes through both the 

extension tube and the stabilizer bar.
Be sure only one person ascends or descends ladder at a 

time. Be certain first person is seated safely, and attached 

to tree with provided Fall Arrest System (FAS) correctly 

before second person ascends or descends ladder.
Never have two people on one side of the platform. Keep 

weight evenly distributed on platform.
Always be aware of the other person’s position. Use 

extreme caution when weapons are used to prevent 

personal injury.

WARNING

Double check assembly steps to be certain you have 

correctly assembled this product.
Study your new stand to become familiar with all of its 

features and design. At ground level, following provided 

use instructions, practice attaching stand to tree and 

removing stand from tree. Practice sitting, standing, and 

using this product before attaching overhead. Save these 

instructions for future reference. You must always use the 

provided Fall Arrest System (FAS) while using this product.
Always use at least three (3) people to install or take down 

a ladder treestand. Always have two people stabilize the 

ladder before climbing to the platform the first time after 

every set-up.
Be absolutely sure the tree blade(s) on stand and the 

stabilizer bar are contacting tree before climbing ladder.
Stabilizer bar must always be correctly and securely 

attached to ladder and tree before climbing ladder.
Make sure ladder bottom is firmly seated on dry, level 

ground. Attach your harness tether to the tree before 

securing the platform to the tree and stepping onto 

platform. Refer to the Full Body Harness instructions.
Never ascend or descend ladder without criss-cross 

straps/ropes securely holding ladder to tree and stabilizer 

bar securely attached. Failure to correctly perform these 

steps can cause the ladder to collapse/buckle-over 

backwards during the initial ascent to attach ratchet strap 

resulting in serious injury or death.
Always lean forward as you climb and attach your harness 

to the tree before securing the platform to the tree and 

stepping onto the platform.
Always maintain three (3) points of contact when 

climbing a ladder treestand. Proper three-point contact 

means having either two feet with one hand or one foot 

with two hands on the step portion of the ladder or 

climbing aid at all times.
Bring ratchet strap(s) up with you in a pocket - Do Not 

carry in your hands!

Содержание Syct RE642

















Отзывы: