background image

  

iHeat Operation Guide: 12063-A 01-13 

  |   

5

About the iHeat thermostat

Mon

System & Fan

Override

More

System Auto

Fan Auto

Occupied

18

6:05

20

Heat on

Current day week

Current time

Temp. setting

Current system 

setting

Current fan setting

Indicates thermostat is 
‘calling for heat’

Current room temp.

Up and down
keys

Modes of operation

Ideally your installer will have 
discussed your needs and 
configured the thermostat to your 
requirements, and spent some 
time with you setting it up for the 
first time.

During the cooler months there 
will be two main modes of 
operation.

1.  System is in manual mode 

(non-programmable mode)—
no timers are set and the 
system is manually turned on 
and off via the thermostat.

2.  System is on heat with the 

fan on auto—system runs on 
timers, and is on all the time.

Location of the thermostat

The thermostat must be installed 
approximately 1.5 m above the 
floor on an internal wall and in the 
location that requires heating. Do 
not place in areas subject to:

 

-

draughts (hallways, regular 
accessed doorways etc.) 

 

-

hot spots (direct sunlight, 
above fireplaces/heaters etc.) 

 

-

dead spots where the air does 
not circulate freely (alcoves, 
corners, behind doors etc.)

LCD screen: Important

The thermostat has an LCD screen. 
Sharp instruments like a pen or 
pencil can damage the thermostat.

Batteries

The thermostat comes 
with two AA alkaline 
batteries installed. 

When the batteries are running 
low a warning will display on the 
main screen for approximately 30 
days. It is recommended that you 
replace the batteries once a year 
to prevent leakage, and to prevent 
the thermostat from shutting 
down. Replace the batteries as 
follows:

1.  Remove the front of the 

thermostat from the base 
by pulling it straight out. All 
programming is retained 
during battery replacement.

2.  Install two new AA alkaline 

batteries. 

3.  Replace  the thermostat back 

on its base making sure the 
terminal screw blocks align 
with the pins on the back 
of the thermostat. After 
two minutes the device will 
automatically return to the 
main screen.

Thermostat temperature range

The thermostat temperature range 
is 4.5 °C to 32 °C.

Main screen selections and display

Batteries (2)

Battery holder

Back of thermostat

UP

Wall

Содержание iHeat





















Отзывы: