Rikon Power Tools 34-260 Скачать руководство пользователя

Страница: 9 / 20

FIG. 1

ASSEMBLY

FIG. 2

FIG. 3

FIG. 4

Release the Mortising Head Assembly.

The Mortiser’s head assembly is secured in the

‘down’ position for transporting, and must be

freed for operation.

1. Loosen the locking hex head Screw (Part #64)

that is located on the left side of the mortising

head, next to the Gas Spring (#57). FIG. 1.

The Mortiser’s head assembly should auto-

matically rise once the locking screw is loosened.

NOTE:

Before assembly begins, make sure that

the Mortiser is positioned on a sturdy work sur-

face, and secured down to prevent any tipping.

Install the Feed Handle

(#1) into the Handle

Shaft (#5), and secure it in place with the Locking

Handle Screw (#4). FIG. 2.

The handle’s lower end has a milled slot on the

outside surface. The locking handle’s screw

should be positioned in this slot when secured.

Install the Front Hand Wheel,

which moves the

sliding table left or right.

1. Attach the Handle Shaft (#84) onto the Gear

Shaft (#83) which extends out from the front of

the machine’s Base (#25). The hex Screw (#86)

threads through both shafts to secure them

together. FIG. 3.

2. Remove the Phillips Screw and Washer (#88,

87) that are on the end of the handle shaft.

3. Slide the Hand Wheel (#85) onto the handle

shaft. The locating key in the handle shaft must

be positioned in the keyway slot in the hand

wheel’s center hole. FIG. 4.

4. Secure the hand wheel in position with the

washer and screw that were removed in Step 1.

GAS

SPRING

LOCKING

SCREW

Содержание 34-260





















Результаты поиска

Содержание 34-260

Отзывы:

Похожие инструкции для 34-260

Бренды по названию

Популярные бренды

Rikon Power Tools 34-260, Руководство оператора

Результаты поиска

Содержание 34-260

Отзывы:

Похожие инструкции для 34-260

Бренды по названию

Популярные бренды