Rikon Power Tools 34-260 Скачать руководство пользователя

Страница: 12 / 20

ADJUSTMENTS

Adjusting the Work Table

The top Table (#42) that holds your work piece,

adjusts forward and backwards on dovetail ways,

FIG. 12, A. The table movement is controlled by

the small knurled Knob (#38) (B).

1. To tighten or loosen the movement of the

table, pressure on the dovetails can be adjusted

with the 2 Screws and Nuts (# 54, 53). FIG. 12,

C. These put pressure on the Drift Plate (#55)

which rests against the table’s dovetails.

2. To secure the table in one spot so that it will

not move, the hex head Screw (#64) (D) can be

fastened down. This is recommended for repeti-

tive drilling of mortises on multiple work pieces.

FIG. 12

FIG. 13

FIG. 14

Adjusting the Lower Sliding Plate

The lower supporting Sliding Plate (#52) adjusts

the top table left and right on a separate set of

dovetail ways. FIG. 13, A. The front Hand Wheel

(#33) (B) controls the side-to-side table move-

ment.

1. To tighten or loosen the movement of the

sliding plate, pressure on the dovetails can be

adjusted with the 3 Screws and Nuts (# 47, 48)

that are located in the front of the sliding plate.

FIG. 13, C. These put pressure on the Drift Plate

(#24) which rests against the plate’s dovetails.

2. To secure the sliding plate in one spot so

that it will not move, the Handle Screw (#49) (D)

can be fastened down. This is recommended for

repetitive drilling in a single location on multiple

work pieces.

Adjusting the Table Clamp

The Table Clamp Assembly (#37) can be ad-

justed to hold different sizes of work against the

fence for the accurate drilling of mortises.

The Table has rows of multiple pre-drilled holes

that the Clamp Base Casting and Pin (#37, 18)

fit into to adjust for clamping different material

widths. FIG. 14.

Continued on page 13

Содержание 34-260





















Результаты поиска

Содержание 34-260

Отзывы:

Похожие инструкции для 34-260

Бренды по названию

Популярные бренды

Rikon Power Tools 34-260, Руководство оператора

Результаты поиска

Содержание 34-260

Отзывы:

Похожие инструкции для 34-260

Бренды по названию

Популярные бренды